74FCT2245ATSOG Renesas

IDT74FCT2245AT/CT FAST CMOS OCTAL BIDIRECTIONAL TRANSCEIVER INDUSTRIAL TEMPERATURE RANGE FAST CMOS OCTAL IDT74FCT2245AT/CT BIDIRECTIONAL TRANSCEIVER FEATURES: DESCRIPTION: A and C grades The IDT octal bidirectional transceivers are built using an advanced dual Low input and output leakage 1 A (max.) metal CMOS technology. The FCT2245T is designed for asynchronous CMOS power levels two-way communication between data buses. The transmit/receive (T/R) True TTL input and output compatibility: input determines the direction of data flow through the bidirectional trans- VOH = 3.3V (typ.) ceiver. Transmit (active high) enables data from A ports to B ports, and VOL = 0.3V (typ.) receive (active low) from B ports to A ports. The output enable (OE) input, Meets or exceeds JEDEC standard 18 specifications when high, disables both A and B ports by placing them in high Z condition. Resistor outputs -15mA IOH, 12mA IOL The FCT2245T has balanced drive outputs with current limiting resistors. Reduced system switching noise This offers low ground bounce, minimal undershoot and controlled output Available in SOIC and QSOP packages fall times- reducing the need for external series terminating resistors. The FCT2245T parts are plug-in replacements for FCT245T parts. FUNCTIONAL BLOCK DIAGRAM T/R OE 0 A B0 A1 1 B 2 A 2 B A3 3 B 4 A 4 B A5 B5 6 A 6 B A7 B 7 IDT and the IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE APRIL 2016 1 2016 Integrated Device Technology, Inc. DSC-5511/8IDT74FCT2245AT/CT FAST CMOS OCTAL BIDIRECTIONAL TRANSCEIVER INDUSTRIAL TEMPERATURE RANGE (1) PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS Symbol Description Max Unit (2) VTERM Terminal Voltage with Respect to GND 0.5 to +7 V (3) VTERM Terminal Voltage with Respect to GND 0.5 to VCC+0.5 V 20 VCC T/R 1 TSTG Storage Temperature 65 to +150 C 19 A0 2 OE IOUT DC Output Current 60 to +120 mA NOTES: A1 18 3 B0 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational A2 4 17 B1 sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. No terminal voltage may exceed A3 16 B2 5 Vcc by +0.5V unless otherwise noted. 2. Inputs and Vcc terminals only. 3. Output and I/O terminals only. B3 A4 6 15 A5 B4 7 14 CAPACITANCE (TA = +25C, F = 1.0MHz) B5 A6 8 13 (1) Symbol Parameter Conditions Typ. Max. Unit A7 9 12 B6 CIN Input Capacitance VIN = 0V 6 10 pF COUT Output Capacitance VOUT = 0V 8 12 pF B7 11 GND 10 NOTE: 1. This parameter is measured at characterization but not tested. SOIC/ QSOP TOP VIEW PIN DESCRIPTION Pin Names Description OE Output Enable Input (Active LOW) T/R Transmit/Receive Input A0 - A7 Side A Inputs or 3-State Outputs B0 - B7 Side BInputs or 3-State Outputs (1) FUNCTION TABLE Inputs OE T/R Outputs L L Bus B Data to Bus A L H Bus A Data to Bus B H X High Z State NOTE: 1. H = HIGH Voltage Level X = Dont Care L = LOW Voltage Level 2