CMS82C55AZ Renesas

MS82C55A, MQ82C55A, MP82C55A Data Sheet June 15, 2006 FN6140.2 CMOS Programmable Peripheral Interface Features The Intersil 82C55A is a high performance CMOS version of Pb-Free Plus Anneal Available (RoHS Compliant) the industry standard 8255A and is manufactured using a (See Ordering Info) self-aligned silicon gate CMOS process (Scaled SAJI IV). Pin Compatible with OKI MSM82C55A The MX82C55A has identical features as the X82C55 with - No Bus Hold Devices on any Port Pins the exception of no bus hold devices on the port pins. It is a 24 Programmable I/O Pins general purpose programmable I/O device which may be used with many different microprocessors. There are 24 I/O Fully TTL Compatible pins which may be individually programmed in two groups of High Speed, No Wait State Operation with 8MHz 80C86 12 and used in three major modes of operation. The high and 80C88 performance and industry standard configuration of the 82C55A make it compatible with the 80C86, 80C88 and Direct Bit Set/Reset Capability other microprocessors. Enhanced Control Word Read Capability Static CMOS circuit design insures low operating power. The L7 Process Intersil advanced SAJI process results in performance equal 2.5mA Drive Capability on All I/O Ports to or greater than existing functionally equivalent products at a fraction of the power. Low Standby Power (ICCSB) .10A Ordering Information PART NUMBERS* PART TEMP. PACKAGE PKG. (Note) MARKING RANGE (C) (Pb-free) DWG. CMP82C55AZ CMP82C55AZ 0 to 70 40 Ld PDIP** E40.6 CMS82C55AZ CMS82C55AZ 0 to 70 44 Ld PLCC N44.65 IMS82C55AZ IMS82C55AZ -40 to 85 CMQ82C55AZ CMQ82C55AZ 0 to 70 44 Ld MQFP Q44.10x10 IMQ82C55AZ IMQ82C55AZ -40 to 85 *Add 96 suffix to part number for tape and reel packaging. **Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. CAUTION: These devices are sensitive to electrostatic discharge follow proper IC Handling Procedures. 1 1-888-INTERSIL or 1-888-468-3774 Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005-2006. All Rights Reserved All other trademarks mentioned are the property of their respective owners.MS82C55A, MQ82C55A, MP82C55A Pinouts MS82C55A (PLCC) MQ82C55A (MQFP) TOP VIEW TOP VIEW 6 5 4 3 2 1 44 43 42 41 40 CS 7 39 RESET GND 8 38 D0 44 43 42 41 40 39 38 37 36 35 34 1 CS RESET 33 A1 9 37 D1 2 D0 A0 10 D2 GND 32 36 PC7 11 35 D3 3 D1 A1 31 NC 12 34 NC D2 4 30 A0 PC6 13 D4 33 D3 5 29 PC7 PC5 14 D5 32 15 D6 PC4 31 6 PC6 28 D4 16 D7 PC0 30 PC5 7 27 D5 V PC1 17 29 CC PC4 8 26 D6 18 1920 21 22 23 24 25 26 27 28 PC0 9 25 D7 10 24 PC1 V CC 11 23 PC2 PB7 12 13 14 15 16 17 18 19 20 21 22 CMP82C55A (PDIP) TOP VIEW PA3 40 PA4 1 PA2 2 39 PA5 PA1 3 38 PA6 PA0 PA7 4 37 RD 36 WR 5 CS 6 35 RESET GND D0 7 34 A1 8 33 D1 A0 9 32 D2 PC7 D3 10 31 PC6 11 D4 30 PC5 12 29 D5 PC4 D6 13 28 PC0 D7 14 27 V PC1 15 26 CC PC2 PB7 16 25 PC3 PB6 17 24 PB0 PB5 18 23 PB1 PB4 19 22 PB2 PB3 20 21 FN6140.2 2 June 15, 2006 PC2 RD PC3 PA0 PB0 PA1 PB1 PA2 PB2 PA3 NC NC PA4 PB3 PB4 PA5 PB5 PA6 PB6 PA7 PB7 WR NC RD PC3 PA0 PB0 PA1 PB1 PA2 PB2 PA3 NC NC PB3 PA4 PB4 PA5 PB5 PA6 PB6 PA7 NC WR