EL7104CSZ-T7 Renesas

DATASHEET EL7104 FN7113 Rev 2.00 High Speed, Single Channel, Power MOSFET Driver July 6, 2006 The EL7104 is a matched driver IC that improves the Features operation of the industry-standard TC-4420/29 clock drivers. Industry-standard driver replacement The Elantec version is a very high speed driver capable of delivering peak currents of 1A into highly capacitive loads. Improved response times The high speed performance is achieved by means of a Matched rise and fall times proprietary Turbo-Driver circuit that speeds up input stages Reduced clock skew by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise Low output impedance and fall delay times. These matched delays maintain the Low input capacitance integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance High noise immunity is accompanied by a 10-fold reduction in supply currents Improved clocking rate over bipolar drivers, yet without the delay time problems commonly associated with CMOS drivers. Low supply current Wide operating range The EL7104 is available in 8-pin SO and 8-pin PDIP packages and is specified for operation over the full -40C to Separate drain connections +85C temperature range. Pb-Free available (RoHS compliant) Ordering Information Applications PART PART TAPE & PKG. Clock/line drivers NUMBER MARKING PACKAGE REEL DWG. EL7104CN EL7104CN 8 Ld PDIP - MDP0031 CCD drivers EL7104CNZ EL7104CN Z 8 Ld PDIP* - MDP0031 Ultrasound transducer drivers EL7104CS 7104CS 8 Ld SOIC - MDP0027 Power MOSFET drivers EL7104CS-T7 7104CS 8 Ld SOIC 7 MDP0027 Switch mode power supplies EL7104CS-T13 7104CS 8 Ld SOIC 13 MDP0027 Resonant charging EL7104CSZ 7104CSZ 8 Ld SOIC - MDP0027 Cascoded drivers (See Note) (Pb-free) EL7104CSZ-T7 7104CSZ 8 Ld SOIC 7 MDP0027 Pinout (See Note) (Pb-free) EL7104 (8-PIN SO, PDIP) EL7104CSZ-T13 7104CSZ 8 Ld SOIC 13 MDP0027 TOP VIEW (See Note) (Pb-free) NOTE: Intersil Pb-free products employ special Pb-free material V+ 1 8 V+ sets molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible IN 2 7 P OUT with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that NC 3 6 N OUT meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. *Pb-free PDIPs can be used for through hole wave solder processing GND 4 5 GND only. They are not intended for use in Reflow solder processing applications. FN7113 Rev 2.00 Page 1 of 7 July 6, 2006EL7104 Absolute Maximum Ratings (T = 25C) A Supply (V+ to GND) . 16.5V Storage Temperature Range -65C to +150C Input Pins -0.3V to +0.3V above V+ Operating Junction Temperature +125C Peak Output Current .4A Power Dissipation Ambient Operating Temperature -40C to +85C SO .570mW PDIP .1050mW CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: T = T = T J C A DC Electrical Specifications V+ = 15V, T = 25C unless otherwise specified. A PARAMETER DESCRIPTION CONDITIONS MIN TYP MAX UNIT INPUT V Logic 1 Input Voltage 2.4 V IH I Logic 1 Input Current V+ 0.1 10 A IH V Logic 0 Input Voltage 0.8 V IL I Logic 0 Input Current 0V 0.1 10 A IL V Input Hysteresis 0.3 V HVS OUTPUT R Pull-Up Resistance I = -100mA 1.5 4 OH OUT R Pull-Down Resistance I = +100mA 2 4 OL OUT I Output Leakage Current V+/GND 0.2 10 A OUT I Peak Output Current Source/Sink 4.0 A PK I Continuous Output Current Source/Sink 200 mA DC POWER SUPPLY I Power Supply Current Input = V+ 4.5 7.5 mA S V Operating Voltage 4.5 16 V S AC Electrical Specifications V = 15V, T = 25C unless otherwise specified. A PARAMETER DESCRIPTION CONDITIONS MIN TYP MAX UNIT SWITCHING CHARACTERISTICS (V = V = 12V V = -3V) DD H L t Rise Time C = 1000pF 7.5 ns R L C = 2000pF 10 20 ns L t Fall Time C = 1000pF 10 ns F L C = 2000pF 15 20 ns L t Turn-On Delay Time See Timing Table 18 25 ns D-ON t Turn-Off Delay Time See Timing Table 18 25 ns D-OFF FN7113 Rev 2.00 Page 2 of 7 July 6, 2006