DATASHEET 120MHz, Ultra-Low Noise Precision Operational Amplifiers HA-5147 Features The HA-5147 operational amplifier features an unparalleled Slew rate . 35V/s combination of precision DC and wideband high speed Wide gain bandwidth (A 10) . 120MHz V characteristics. Utilizing the Intersil D. I. technology and Low noise 3.2nV/Hz at 1kHz advanced processing techniques, this unique design unites low noise (3.2nV/ Hz) precision instrumentation performance with Low V 30V OS high speed (35V/s) wideband capability. High CMRR . 120dB This amplifiers impressive list of features include low V OS High gain 1500V/mV (30mV), wide gain bandwidth (120MHz), high open loop gain (1500V/mV) and high CMRR (120dB). Additionally, this flexible Applications device operates over a wide supply range (5V to 20V) while High speed signal conditioners consuming only 140mW of power. Wide bandwidth instrumentation amplifiers Using the HA-5147 allows designers to minimize errors while Low level transducer amplifiers maximizing speed and bandwidth in applications requiring gains greater than ten. Fast, low level voltage comparators This device is ideally suited for low level transducer signal Highest quality audio preamplifiers amplifier circuits. Other applications which can utilize the Pulse/RF amplifiers HA-5147s qualities include instrumentation amplifiers, pulse For further design ideas see application note AN553 or RF amplifiers, audio preamplifiers and signal conditioning circuits. Pin Configuration This device can easily be used as a design enhancement by HA-5147 (CERDIP) directly replacing the 725, OP25, OP06, OP07, OP27 and TOP VIEW OP37 where gains are greater than ten. 1 8 BAL BAL 2 7 -IN V+ - + 3 6 +IN OUT 4 5 V- NC Ordering Information TEMP. RANGE PKG. DWG. PART NUMBER PART MARKING (C) PACKAGE HA7-5147-2 HA7- 5147-2 -55 to +125 8 Ld CerDIP F8.3A HA7-5147R5254 (Note 1) HA7- 5147R5254 -55 to +125 8 Ld CerDIP with Pb-free Hot Solder DIP Lead Finish (SnAgCu) F8.3A NOTE: 1. Intersil Pb-free hermetic packaged products employ SnAgCu or Au termination finish, which are RoHS compliant termination finishes and compatible with both SnPb and Pb-free soldering operations. Ceramic dual in-line packaged products (CerDIPs) do contain lead (Pb) in the seal glass and die attach glass materials. However, lead in the glass materials of electronic components are currently exempted per the RoHS directive. Therefore, ceramic dual inline packages with Pb-free termination finish are considered to be RoHS compliant. November 6, 2015 CAUTION: These devices are sensitive to electrostatic discharge follow proper IC Handling Procedures. 1 1-888-INTERSIL or 1-888-468-3774 Copyright Intersil Americas LLC 2003, 2006, 2015. All Rights Reserved FN2910.10 Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners.HA-5147 Thermal Information Absolute Maximum Ratings T = +25C A Voltage Between V+ and V- Terminals . 44V Thermal Resistance (Typical) (C/W) (C/W) JA JC Differential Input Voltage (Note 2) . 0.7V CERDIP Package (Note 3) 135 50 Output Current Full Short-circuit Protection Maximum Junction Temperature (Hermetic Package) +175C Maximum Storage Temperature Range . -65C to +150C Maximum Lead Temperature (Soldering 10s) +300C Operating Conditions Temperature Range HA-5147-2 -55C to +125C CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 2. For differential input voltages greater than 0.7V, the input current must be limited to 25mA to protect the back-to-back input diodes. 3. is measured with the component mounted on an evaluation PC board in free air. JA Electrical Specifications V = 15V, C 50pF, R 100 . SUPPLY L S TEMP. PARAMETER TEST CONDITIONS (C) MIN TYP MAX UNITS INPUT CHARACTERISTICS Offset Voltage 25 - 30 100 V Full - 70 300 V Average Offset Voltage Drift Full - 0.4 1.8 V/C Bias Current 25 - 15 80 nA Full - 35 150 nA Offset Current 25 - 12 75 nA Full - 30 135 nA Common Mode Range Full 10.3 11.5 - V Differential Input Resistance (Note 4)250.84-M Input Noise Voltage (Note 5) 0.1Hz to 10Hz 25 - 0.09 0.25 V P-P Input Noise Voltage Density (Note 6) f = 10Hz 25 - 3.8 8.0 nV/ Hz f = 100Hz - 3.3 4.5 nV/ Hz f = 1000Hz - 3.2 3.8 nV/ Hz Input Noise Current Density (Note 6)f = 10Hz 25 - 1.7 - pA/ Hz f = 100Hz - 1.0 - pA/ Hz f = 1000Hz - 0.4 0.6 pA/ Hz TRANSFER CHARACTERISTICS Minimum Stable Gain 25 10 - - V/V Large Signal Voltage Gain V = 10V, R = 2k 25 700 1500 - V/mV OUT L Full 300 800 - V/mV Common Mode Rejection Ratio V = 10V Full 100 120 - dB CM Gain-bandwidth Product f = 10kHz 25 120 140 - MHz f = 1MHz - 120 - MHz Submit Document Feedback FN2910.10 2 November 6, 2015