ISL71830SEHF/PROTO Renesas

DATASHEET ISL71830SEH FN8758 Rev 5.00 Radiation Tolerant 5V 16-Channel Analog Multiplexer Mar 27, 2018 The ISL71830SEH is a radiation tolerant, 16-channel Features multiplexer that is fabricated using the proprietary P6 SOI DLA SMD 5962-15247 process technology to provide excellent latch-up performance. It operates with a single supply range from 3V to 5.5V and has Fabricated using P6 SOI process technology a 4-bit address line plus an enable that can be driven with Rail-to-rail operation adjustable logic thresholds to conveniently select one of 16 No latch-up available channels. An inactive channel is separated from the active channel by a high impedance, which inhibits any Low r <120 (maximum) DS(ON) interaction between the channels. Single supply operation 3V to 5.5V The ISL71830SEH low r allows for improved signal DS(ON) - Adjustable logic threshold control integrity and reduced power losses. The ISL71830SEH is also Cold sparing capable -0.4V to 7V designed for cold sparing, making it excellent for redundancy in high reliability applications. It is designed to provide a high Analog overvoltage range -0.4V to 7V impedance to the analog source in a powered off condition, Switch input off leakage . 120nA making it easy to add additional backup devices without Transition times (t ) 70ns incurring extra power dissipation. The ISL71830SEH also has AHL analog overvoltage protection on the input that disables the Internally grounded metal lid switch during an overvoltage event to protect upstream and Break-before-make switching downstream devices. ESD protection 5kV (HBM) The ISL71830SEH is available in a 28 Ld CDFP and operates Operating temperature range -55C to +125C across the extended temperature range of -55C to +125C. Radiation tolerance A 32-channel version is also available offered in a 48 Ld CQFP. - Low dose rate (0.01rad(Si)/s) (Note 1) 75krad(Si) Refer to the ISL71831SEH datasheet for more information. For + 2 a list of differences between the ISL71830SEH and - SEL/SEB LET (V = 6.5V) . 60MeVcm /mg TH ISL71831SEH, refer to Table 1 on page 2. NOTE: 1. All lots are assurance tested to 75krad (0.01rad(Si)/s) Related Literature wafer-by-wafer. For a full list of related documents, visit our website Applications ISL71830SEH product page Telemetry signal processing Harsh environments Down-hole drilling ISL71830SEH 90 IN01 80 IN02 +125C 70 IN03 +25C OUT ADC 60 . 50 40 IN16 30 -55C 20 4 10 0 ADDRESS 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 EN COMMON-MODE VOLTAGE (V) + FIGURE 1. TYPICAL APPLICATION FIGURE 2. r vs COMMON-MODE VOLTAGE (V = 5V) DS(ON) FN8758 Rev 5.00 Page 1 of 21 Mar 27, 2018 r () DS(ON) ISL71830SEH Ordering Information SMD ORDERING NUMBER PART NUMBER PACKAGE PKG. (Note 3) (Note 2) TEMP RANGE (C) (RoHS COMPLIANT) DWG. 5962L1524701VXC ISL71830SEHVF -55 to +125 28 Ld CDFP K28.A N/A ISL71830SEHF/PROTO (Note 4) -55 to +125 28 Ld CDFP K28.A 5962L1524701V9A ISL71830SEHVX -55 to +125 Die N/A ISL71830SEHX/SAMPLE (Note 4) -55 to +125 Die N/A ISL71830SEHEV1Z (Note 5) Evaluation Board NOTES: 2. These Pb-free Hermetic packaged products employ 100% Au plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. 3. Specifications for Rad Hard QML devices are controlled by the Defense Logistics Agency Land and Maritime (DLA). The SMD numbers listed in the Ordering Information table must be used when ordering. 4. The /PROTO and /SAMPLE are not rated or certified for Total Ionizing Dose (TID) or Single Event Effect (SEE) immunity. These parts are intended for engineering evaluation purposes only. The /PROTO parts meet the electrical limits and conditions across the temperature range specified in the DLA SMD and are in the same form and fit as the qualified device. The /SAMPLE die is capable of meeting the electrical limits and conditions specified in the DLA SMD at +25C only. The /SAMPLE is a die and does not receive 100% screening across the temperature range to the DLA SMD electrical limits. These part types do not come with a certificate of conformance because there is no radiation assurance testing and they are not DLA qualified devices. 5. The evaluation board uses the /PROTO parts. The /PROTO parts are not rated or certified for Total Ionizing Dose (TID) or Single Event Effect (SEE) immunity. TABLE 1. KEY DIFFERENCES BETWEEN FAMILY OF PARTS PART NUMBER NUMBER OF CHANNELS OUTPUT LEAKAGE PACKAGE ISL71831SEH 32 120nA 48 Ld CQFP ISL71830SEH 16 60nA 28 Ld CDFP FN8758 Rev 5.00 Page 2 of 21 Mar 27, 2018