ISL85014EVAL1Z Renesas

600kHz 300kHz HICCUP DISABLE ENABLE LATCH-OFF FCCM DEM USERS MANUAL ISL85014EVAL1Z UG113 Rev.0.00 Evaluation Board User Guide Feb 15, 2017 Description Key Features The ISL85014 is a 3.8V to 18V input, 14A synchronous buck Switch selectable EN (enabled/disabled) regulator for applications with input voltage from multi-cell Frequency synchronization option batteries or regulated 5V and 12V power rails. The device also Jumper selectable mode (DEM/Forced CCM) provides an integrated bootstrap diode for the high-side gate driver to reduce the external parts count. The ISL85014EVAL1Z Jumper selectable OCP mode (Hiccup/Latch-off) platform allows quick evaluation of the high-performance Jumper selectable frequency (600kHz/300kHz) features of the ISL85014 buck regulator. Connectors and test points for easy probing Compact design Specifications This board has been configured and optimized for the following Related Literature operating conditions: For a full list of related documents, visit our website Input voltage ranges from 4.5V to 18V - ISL85014 product pages 1.8V nominal output voltage Ordering Information Up to 14A output current capability Default internally set to 600kHz switching frequency PART NUMBER DESCRIPTION Default internally set to 3ms soft-start ISL85014EVAL1Z Evaluation board for ISL85014FRZ Operating temperature range: -40C to +85C R R R 2 1 3 C 1 15 14 13 12 11 10 VIN EN DNC DNC COMP FB PVIN PVIN 9 L1 V OUT 4.5V TO 18V C PHASE 8 IN 1.8V/14A COUT GND C GND 7 4 GND SYNC MODE FREQ PG VDD BOOT 12 3 4 5 6 C 3 FIGURE 1. BLOCK DIAGRAM UG113 Rev.0.00 Page 1 of 8 Feb 15, 2017ISL85014EVAL1Z Connector and Test Point Quick Setup Guide Descriptions Refer to the following instructions to configure and power-up the board for proper operation. The ISL85014EVAL1Z evaluation board includes I/O connectors and test points as shown in Table 1. 1. Set the power supply voltage to 12V and turn off the power supply. Connect the positive output of the power supply to J1 TABLE 1. CONNECTORS AND TEST POINTS (PVIN) and the negative output to J3 (GND). REFERENCE 2. Connect an electronic load to J2 (VOUT) for the positive DESIGNATOR DESCRIPTION connection and J4 (GND) for the negative connection. J1 Input voltage positive connection 3. Measure the output voltage (test points VOUT and GND) with the voltmeter. J2 Output voltage positive connection 4. Place scope probes on VOUT test point (J7) and other test J3 Input voltage return connection points of interest. J4 Output voltage return connection 5. Toggle selection switch SW5 to ON position. J6 Two-position socket connector for PHASE to GND test 6. Set the load current to 0.1A and turn on the power supply. The output voltage should be in regulation with a nominal 1.8V J7 Two-position socket connector for VOUT to GND test output. PVIN PVIN positive test point 7. Slowly increase the load up to 14A while monitoring the GND GND test point output voltage, which should remain in regulation with a nominal 1.8V output. VIN VIN positive test point 8. Slowly sweep VIN from 4.5V to 18V. The output voltage should VOUT Output voltage positive test point remain in regulation with a nominal 1.8V output. SYNC External synchronization clock connection 9. Decrease the input voltage to 0V to shut down the regulator. EN Enable test point Frequency Synchronization VDD Internal LDO output test point The ISL85014 can be synchronized to an external clock with PG Power-good output frequency ranges from 100kHz to 1MHz by applying the external clock to test point SYNC on the ISL85014EVAL1Z evaluation Selection Switch and Jumper board. The external clock should meet the specifications of pulse width and voltage level described in the ISL85014 datasheet. Descriptions Switch SW5 (Enable) Evaluating Other Output The switch enables and disables the ISL85014: Voltages - When the switch is in the ON position, the ISL85014 is enabled. The ISL85014EVAL1Z has a nominal 1.8V output voltage. The - When the switch is in the OFF position, the ISL85014 is output voltage is programmable by an external resistor divider disabled. and R as shown in Figure 1 on page 1. R is formed by R 1 2 1 usually chosen first, then the value for R can be calculated 2 Jumper J9 based on R and the desired output voltage using Equation 1: 1 The jumper provides the selection of different operating modes, detailed as follows: R 0.6V 1 (EQ. 1) R ---------------------------------- = 2 - When the jumper is in the FCCM position, the ISL85014 V 0.6V OUT operates in Forced CCM. - When the jumper is in the DEM position, the ISL85014 operates in Diode Emulation mode and enables automatic transition from CCM to DCM at light-load conditions. Jumper J10 sets the switching frequency at either 600kHz or 300kHz. Jumper J11 sets the OCP scheme in either Hiccup mode or Latch-Off mode. UG113 Rev.0.00 Page 2 of 8 Feb 15, 2017