QB-R5F110PJ-TB

Users Manual RL78/L1C R20UT2521XJ0200 R20UT2521XJ0200 RL78/L1C Target board QB-R5F110PJ-TB Users Manual Rev2.00 2013.07.12 QB-R5F110PJ-TB Rev2.00 2013.07.12 The QB- R5F110PJ -TB is a target board used for evaluating microcontroller operations, using the E1, the Renesas Electronics E1 on-chip debug emulator with programming function. (1) RL78/L1C target board (QB-R5F110PJ-TB) features RL78/L1C (QB-R5F110PJ-TB) Incorporates RL78/L1C (R5F110PJ). RL78/L1C(R5F110PJ) A 12MHz resonator and a 32.768kHz resonator are mounted. 12MHz 32.768kHz Supports both flash memory programming and on-chip debugging (using TOOL0 pin) Highly extendable peripheral board connectors are equipped with microcontroller pins (TOOL0 ) (2) hardware specifications CPU R5F110PJ Main clock operating frequency MAX 24MHz. (when use resonator mounted on board) CPU R5F110PJ 24MHz() Sub clock operating frequency 32.768 KHz 32.768KHz Embedded parts CN1: Peripheral board connectors (2.54 mm pitch), 20-pin socket 3 (pad only) CN1: (2.54mm ) 20pin x3() CN2: Peripheral board connectors (2.54 mm pitch), 18-pin socket 2 (pad only) CN2: (2.54mm ) 18pin x2() CN3: 14-pin connector (for E1 connection) CN3: 14pin (E1 ) Power LED: Red 1 (LED3) Power LED: x1(LED3) Test LED: Yellow 2 (LED1 connected to P41, LED2 connected to P42) LED: x2(LED1 P41,LED2 P42 ) Test SW: SW1 (connected to INTP0) SW: SW1(INTP0 ) Main clock (OSC1): 12 MHz resonator(connected to X1 and X2) (OSC1): 12MHz (X1,X2 ) Subclock (OSC2): 32.768 KHz oscillator (connected to XT1 and XT2) (OSC2): 32.768kHz (XT1,XT2 ) Operating voltage 1.6 to 3.6 V(when 12MHz resonator used at OSC1) 1.6V3.6V(OSC1:12MHz ) (3) Dimensions and parts layout Main Clock Sub Clock LED2 P42 35 1 36 LED2 P42 LED 2 35 1 30 OSC2 20 36 2 10 CN2 Test LED LED1 P41 CN2 :LED2 JP1 P137 30 OSC2 20 CN2 10 LED1 P41 CN2 upper:LED2 JP1 :LED1 P137 LED3 CP12 lower:LED1 13 SW1 LED3 SW1(INTP0) CP12 SW1 USB5V 13 UDP SW1(INTP0) Power LED USB5V UDP UDM Power LED RL78 UDM RL78 /L1C JAPAN RL78/L1C /L1C USB JAPAN QB-R5F110PJ-TB(e) RL78/L1C 1 USB SS-77234-1 QB-R5F110PJ-TB(e) CAPL VL1 VL2 VL3 VL4 1 CAPH GND VL1 VL2 VL3 VDD SS-77234-1 CAPL VL1 VL2 VL3 VL4 VDD 14pin S55 S36 CAPH GND VL1 VL2 VL3 VDD GND VDD S35 S16 14pin connector S55 S36 GND S15 C0 CN1 CN1 S35 S16 S15 C0 CN1 CN1 71.12mm LCD 71.12mm LCD driver pattern Pattern on the board: Splitting this wiring leaves open the relevant circuit ( ). : To reconnect the circuit, short the circuit by soldering ( ). When using P41 and P42, cut off the short pad on the right side of LED. P41,P42 LED Showing of the pad on circuit diagram. open: short: When supplying a power from USB connector to a device, short JP1 by soldering. USB JP1 (4) Notes on use Renesas Electronics will not provide any support for this board, but the board can be exchanged with a new product only when it has an initial failure. R20UT2521XJ0200 Rev.2.00 Page 1 of 3 R20UT2521XJ0200 Rev.2.00 Page 1 of 3 2013.07.12 2013.07.12 55.88mm OCD/Flash Program P123 XT1 XT2 P124 AVREFP AVREFM AVDD UREGC UVBUS 55.88mm OCD/Flash Program P123 XT1 XT2 P124 AVREFP AVREFM AVDD UREGC UVBUS Users Manual RL78/L1C R20UT2521XJ0200 RL78/L1C Target board R20UT2521XJ0200 QB-R5F110PJ-TB Users Manual Rev2.00 2013.07.12 QB-R5F110PJ-TB Rev2.00 2013.07.12 , Setting of Clock and port. - Setting of main clock OSC1 pad OSC3 pad (back of board) P121, P122 pad OSC1 pad P121, P122 pad OSC3 pad () Default setting: X1 pad : short S X1 pad : open P121 pad : open X1 pad : short S X1 pad : open P121 pad : open Using resonator of 3-pin (OSC1) X2 pad : short S X2 pad : open P122 pad : open X2 pad : short S X2 pad : open P122 pad : open 3 (OSC1) Using resonator of 2-pin (OSC3) X1 pad : open Mounting of OSC3, C5 and C6 P121 pad : open X1 pad : open P121 pad : open 2 (OSC3) OSC3, C5, C6 X2 pad : open S X1 pad : short P122 pad : open X2 pad : open P122 pad : open S X1 pad : short S X2 pad : short S X2 pad : short Using P121 and P122 X1 pad : open S X1 pad : open P121 pad : X1-P121 short X1 pad : open S X1 pad : open P121 pad : X1-P121 short P121,P122 X2 pad : open S X2 pad : open P122 pad : X2-P122 short X2 pad : open S X2 pad : open P122 pad : X2-P122 short Dont use resonator X1 pad : open S X1 pad : open P121 pad : X1-GND short X1 pad : open S X1 pad : open P121 pad : X1-GND short (OSC1,OSC3) (OSC1 and OSC3) X2 pad : open S X2 pad : open P122 pad : X2-GND short X2 pad : open S X2 pad : open P122 pad : X2-GND short - Setting of sub clock OSC2 pad P123, P124 pad OSC2 pad P123, P124 pad Default setting: XT1 pad : short P123 pad : open XT1 pad : short P123 pad : open Using resonator OSC2 XT2 pad : short P124 pad : open XT2 pad : short P124 pad : open (OSC2) Using P123 and P124 XT1 pad : open P123 pad : XT1-P123 short XT1 pad : open P123 pad : XT1-P123 short P123, P124 XT2 pad : open P124 pad : XT2-P124 short XT2 pad : open P124 pad : XT2-P124 short Dont use resonator (OSC2) XT1 pad : open P123 pad : XT1-GND short (OSC2) XT1 pad : open P123 pad : XT1-GND short XT2 pad : open P124 pad : XT2-GND short XT2 pad : open P124 pad : XT2-GND short The figure of pad of OSC1, OSC2 and OSC3 OSC1, OSC2, OSC3 pad 3. The figure of pad of OSC3 1. The figure of pad of OSC1 2. The figure of pad of OSC2 1. OSC1 pad 2. OSC2 pad 3. OSC3 pad OSC3 XT1 pad OSC3 XT2 pad XT1 pad XT2 pad X1 pad X2 pad X1 pad X2 pad OSC2 OSC2 OSC1 OSC1 C5 C5 C6 C3 C6 C3 C4 C4 1 3 X1 X1 X2 X2 GND GND GND GND XT2 XT2 XT1 XT1 P121 P121 GND GND P122 GND P122 GND P124 P124 P123 P123 S X2 pad S X1 pad S X1 pad S X2 pad 5 7 4 2 8 P124 pad P123 pad 6 P122 pad P121 pad P121 pad P122 pad P123 pad P124 pad 1. Connect to X1 pin (18pin) of the microcomputer. 5. Connect to XT1 pin (15pin) of the microcomputer. X1 (18pin) XT1 (15pin) 2. Connect to CN2-19 (P121) 6. Connect to CN2-16 (P123) CN2-19 (P121) CN2-16 (P123) 3. Connect to X2 pin (17pin) of the microcomputer. X2 (17pin) XT2 (14pin) 7. Connect to XT2 pin (14pin) of the microcomputer. 4. Connect to CN2-18 (P122) 8. Connect to CN2-15 (P124) CN2-18 (P122) CN2-15 (P124) R20UT2521XJ0200 Rev.2.00 Page 2 of 3 R20UT2521XJ0200 Rev.2.00 Page 2 of 3 2013.07.12 2013.07.12