Datasheet R01DS0168EJ0210 RL78/L13 Rev.2.10 RENESAS MCU Aug 12, 2016 Integrated LCD controller/driver, True Low Power Platform (as low as 112.5 A/MHz, and 0.61 A for RTC + LVD), 1.6 V to 5.5 V operation, 16 to 128 Kbyte Flash, 31 DMIPS at 24 MHz, for All LCD Based Applications 1. OUTLINE <R> 1.1 Features Ultra-low power consumption technology Serial interface VDD = single power supply voltage of 1.6 to 5.5 V which can CSI: 2 channels operate a 1.8 V device at a low voltage UART/UART (LIN-bus supported): 3, 4 channels/1 channel 2 2 HALT mode I C/Simplified I C communication: 1 channel/2 channels STOP mode Timer SNOOZE mode 16-bit timer: 8 channels (with remote control output function) RL78 CPU core 16-bit timer KB20 (IH): 1 channel CISC architecture with 3-stage pipeline (IH-only PWM output function) Minimum instruction execution time: Can be changed from high 12-bit interval timer: 1 channel speed (0.04167 s: 24 MHz operation with high-speed on- Real-time clock 2: 1 channel (calendar for 99 years, alarm chip oscillator) to ultra-low speed (30.5 s: 32.768 kHz function, and clock correction function) operation with subsystem clock) Watchdog timer: 1 channel (operable with the dedicated low- Address space: 1 MB speed on- chip oscillator) General-purpose registers: (8-bit register 8) 4 banks A/D converter On-chip RAM: 1 to 8 KB 8/10-bit resolution A/D converter (VDD = 1.6 to 5.5 V) Code flash memory Analog input: 9 to 12 channels Note 1 Code flash memory: 16 to 128 KB Internal reference voltage (1.45 V) and temperature sensor Block size: 1 KB Comparator Prohibition of block erase and rewriting (security function) 2 channels On-chip debug function Operation mode: Comparator high-speed mode, comparator Self-programming (with boot swap function/flash shield window low-speed mode, or window mode function) External reference voltage and internal reference voltage are Data flash memory selectable Data flash memory: 4 KB LCD controller/driver Back ground operation (BGO): Instructions can be executed Note 2 Note 2 Segment signal output: 36 (32) to 51 (47) from the program memory while rewriting the data flash memory. Note 2 Common signal output: 4 (8) Number of rewrites: 1,000,000 times (TYP.) Internal voltage boosting method, capacitor split method, and Voltage of rewrites: VDD = 1.8 to 5.5 V external resistance division method are switchable High-speed on-chip oscillator I/O port Select from 48 MHz, 24 MHz, 16 MHz, 12 MHz, 8 MHz, 6 MHz, I/O port: 49 to 65 (N-ch open drain I/O withstand voltage of 6 4 MHz, 3 MHz, 2 MHz, and 1 MHz V : 2, N-ch open drain I/O VDD withstand voltage : 12 to 18) High accuracy: +/-1.0 % (VDD = 1.8 to 5.5 V, TA = -20 to +85C) Can be set to N-ch open drain, TTL input buffer, and on-chip Operating ambient temperature pull-up resistor TA = -40 to +85C (A: Consumer applications) Different potential interface: Can connect to a 1.8/2.5/3 V TA = -40 to +105C (G: Industrial applications) device On-chip key interrupt function Power management and reset function On-chip clock output/buzzer output controller On-chip power-on-reset (POR) circuit Others On-chip voltage detector (LVD) (Select interrupt and reset from 14 levels) On-chip BCD (binary-coded decimal) correction circuit DMA (Direct Memory Access) controller Notes 1. Can be selected only in HS (high-speed main) mode 4 channels 2. The values in parentheses are the number of signal Number of clocks during transfer between 8/16-bit SFR and outputs when 8 com is used. internal RAM: 2 clocks Remark The functions mounted depend on the product. See Multiplier and divider/multiply-accumulator 1.6 Outline of Functions. 16 bits 16 bits = 32 bits (Unsigned or signed) 32 bits 32 bits = 32 bits (Unsigned) 16 bits 16 bits + 32 bits = 32 bits (Unsigned or signed) * There are differences in specifications between every product. Please refer to specification for details. R01DS0168EJ0210 Rev.2.10 Page 1 of 123 Aug 12, 2016 RL78/L13 1. OUTLINE ROM, RAM capacities Flash ROM Data Flash RAM RL78/L13 64 pins 80 pins Note 128 KB 4 KB 8 KB R5F10WLG R5F10WMG 96 KB 4 KB 6 KB R5F10WLF R5F10WMF 64 KB 4 KB 4 KB R5F10WLE R5F10WME 48 KB 4 KB 2 KB R5F10WLD R5F10WMD 32 KB 4 KB 1.5 KB R5F10WLC R5F10WMC 16 KB 4 KB 1 KB R5F10WLA R5F10WMA Note This is about 7 KB when the self-programming function and data flash function are used. (For details, see CHAPTER 3 in the RL78/L13 Users Manual.) R01DS0168EJ0210 Rev.2.10 Page 2 of 123 Aug 12, 2016