Datasheet R01DS0258EJ0130 RL78/G1D Rev.1.30 RENESAS MCU Feb 23, 2018 The RL78/G1D is a microcontroller incorporating the RL78 CPU core and low power consumption RF transceiver supporting the Bluetooth ver.4.2 (Low Energy Single mode) specifications. 1. OUTLINE 1.1 Features Low Power Technology (3.0V / MCU part: STOP ) Data Memory Access (DMA) Controller Up to 4 fully programmable channels RF transmitter active: 4.3 mA (TYP.) Transfer unit: 8- or 16-bit RF receiver active: 3.5 mA (TYP.) RF sleep (POWER DOWN mode) operation: 0.3 A Multiple Communication Interfaces (TYP.) 2 Simplified I C2 CSI (7-, 8-bit) 2, On-Chip RF Transceiver UART (7-, 8-, 9-bit) 2 <R> Bluetooth v4.2 Specification (Low Energy Single mode) 2 I C 1 2.4 GHz ISM Band, GFSK modulation, TDMA/TDD Frequency Hopping (included AES encryption circuit) Supply voltage Management Adaptivity, exclusively for use in operation as a Low voltage detection (LVD) with 12 setting options slave device (Notification to Interrupt and/or reset function) Single ended RF interface Power-on reset (POR) monitor/generator <R> 16-bit RL78-S2 CPU Core Extended-Function Timers CISC Architecture (Harvard) with 3-stage pipeline Multi-function 16-bit timers: 8 channels Minimum instruction execution time: Can be changed Real-time clock (RTC): 1 channel (full calendar and from high speed (0.03125 s: 32 MHz operation alarm function with watch correction function) with high-speed on-chip oscillator) to Interval Timer: 12-bit, 1 channel ultra-low speed (30.5 s: 32.768 kHz operation Watchdog timer: 1 channel (window function) with subsystem clock) Multiply Signed & Unsigned: 16 x 16 to 32-bit result in Rich Analog 1 clock cycle 8/10-bit resolution A/D converter (V = 1.6 to 3.6 V) DD 1-wire on-chip debug function Analog input: 8 channels Internal voltage reference (1.45 V) and temperature Main Flash Memory Note sensor 128 KB / 192KB / 256 KB (Block size: 1 KB) Note Can be selected only in HS (high-speed main) mode On-chip single voltage flash memory with protection from block erase/writing Safety Functions Self-programming with secure boot swap function Comply with the IEC60730 and IEC61508 safety and flash shield window function standards Data Flash Memory General Purpose I/O Data Flash with background operation I/O port: 32 (N-ch open drain I/O withstand voltage of Data flash size: 8 KB size (Erase block size: 1 KB) 6 V : 2, N-ch open drain I/O VDD withstand voltage : 9 Erase Cycles: 1 Million (typ.) Different potential interface support: Can connect to a Erase/programming voltage: 1.8 V to 3.6 V 1.8/2.5 V device RAM Standby function 12 KB / 16KB / 20 KB size MCU part: Low power consumption mode: HALT, Supports operands or instructions STOP Back-up retention in all modes Power saving mode: SNOOZE RF part :Low power saving mode with 6 setting (min. On-chip Oscillator 0.1 A) High accuracy on-chip Oscillator for MCU 15kHz low-speed on-chip oscillator for MCU Operating Voltage / Operating Ambient Temperature 32.768 kHzOn-chip oscillator for the RF slow clock 1.6 V to 3.6 V / 40 to +85C Package Type and Pin Count 48-pin HWQFN (6 6) (0.4mm pitch) R01DS0258EJ0130 Rev.1.30 Page 1 of 74 Feb 23, 2018 RL78/G1D CHAPTER 1 OUTLINE ROM, RAM capacities Flash ROM Data Flash RAM RL78/G1D 128 KB 8 KB 12 KB R5F11AGG 192 KB 8 KB 16 KB R5F11AGH Note 256 KB 8 KB 20 KB R5F11AGJ Note 19 KB when the self-programming function is used. R01DS0258EJ0130 Rev.1.30 Page 2 of 74 Feb 23, 2018