Users Manual RL78/G10 R20UT2894XJ0100 RL78/G10 Target board R20UT2894XJ0100 RTE510Y470TGB00000R Users Manual Rev 1.00 2014.2.28 RTE510Y470TGB00000R Rev 1.00 2014.2.28 The RTE510Y470TGB00000R is a target board used for evaluating microcontroller operations, using the E1, the Renesas E1 Electronics on-chip debug emulator with programming function (hereinafter referred to as E1). (1) RL78/G10 target board (RTE510Y470TGB00000R) features RL78/G10 (RTE510Y470TGB00000R) Incorporates RL78/G10 (R5F10Y47) RL78/G10(R5F10Y47) A 20MHz resonator is mounted 20MHz Equipped with universal area (2.54 mm pitch) Supports both flash memory programming and on-chip debugging (using TOOL0 pin) (2.54mm ) Highly extendable peripheral board connectors are equipped with microcontroller pins , (TOOL0 ) It can be used as a DIP conversion board of 2.54mm pitch by cutting off a board. , 2.54 DIP (2) hardware specifications CPU R5F10Y47 Main clock operating frequency 20 MHz CPU R5F10Y47 20MHz Embedded parts CN1, CN2, CN4: Peripheral board connectors (2.54 mm pitch), 8-pin socket 3 (pad only) CN1,CN2,CN4: (2.54mm ) 8pin x3( ) CN3: 14-pin connector (for E1 connection) CN3: 14pin (E1 ) Power LED: Red 1 (LED2) Power LED: x1(LED2) Test LED: Yellow 1 (LED1 connected to P00) LED: x1(LED1 P00 ) Test SW: SW1 (connected to INTP0) SW: SW1(INTP0 ) (OSC1): 20MHz (X1,X2 ) Main clock (OSC1): 20 MHz resonator(connected to X1 and X2) 2.0V5.5V Operating voltage 2.0 to 5.5 V (3) Dimensions and parts layout Cutting points LED LED :LED2(POWER) upper:LED2(POWER) CN4 CN2 CN4 <Top View> CN2 <Top View> :LED1(P00) lower:LED1(P00) 1 GND 16 1 GND 16 RTE510Y470TGB00000R RTE510Y470TGB00000R N.C. N.C. Universal area TOOL0 POWER TOOL0 POWER RESET 14pin connector RESET 14pin P00 P00 T RESET T RESET N.C. N.C. N.C. N.C. SW1 SW1 GND VDD GND VDD VDD VDD 8 9 SG-13-0556-01 8 9 SG-13-0556-01 SW1(INTP0) SW1(INTP0) CN1 CN1 RL78/G10 RL78/G10 <.ottom View> <.ottom View> GND N.C. GND TOOL0 RESET JP3 N.C. RESET JP4 TOOL0 RESET T RESET JP3 P122 P121 RESET 21.98mm N.C. JP2 JP4 T RESET N.C. JP1 P122 P121 21.98mm N.C. JP2 GND X2 X1 N.C. JP1 VDD VDD GND X2 X1 VDD VDD 60mm 60mm Pattern on the board: Splitting this wiring leaves open the relevant circuit ( ). : To reconnect the circuit, short the circuit by soldering ( ). When using P00 cut off the short pad on the left side of LED. P00 LED Showing of the pad on circuit diagram. open: short: : : (4) Notes on use Renesas Electronics will not provide any support for this board, but the board can be exchanged with a new product only when it has an initial failure. Before cutting off a board by hand, please make a cut by using a cutter. It is also possible to cut off it by using nippers. , R20UT2894XJ0100 Rev.1.00 Page 1 of 3 R20UT2894XJ0100 Rev.1.00 Page 1 of 3 2014.2.28 2014.2.28 Users Manual R20UT2894XJ0100 RL78/G10 RL78/G10 Target board R20UT2894XJ0100 RTE510Y470TGB00000R Users Manual Rev 1.00 2014.2.28 Rev 1.00 2014.2.28 RTE510Y470TGB00000R JP1 JP4 JP1 JP4 - Setting of JP1, JP2, JP3 and JP4 are following. JP1 JP2 JP3 JP4 JP1 JP2 JP3 JP4 When using P125/KR1/RESET pin as RESET pin (default) Short Short Open Short P125/KR1/RESET RESET ( ) When using P125/KR1/RESET pin as P125 or KR1 pin Open Open Short Open P125/KR1/RESET P125/KR1 - When using DIP conversion board of 2.54mm pitch by cutting off a board. 2.54mm DIP Please short of RESET pad. (default open) RESET ( ) 10.12mm 7.62mm 10.12mm 7.62mm 16 1 10 1 1 16 GND 10 1 GND RESET Please short of RESET pad. RESET 21.98mm 21.98mm 2.54mm 2.54mm VDD 8 9 9 8 VDD 8 9 8 9 <Top View> <Bottom View> <Bottom View> <Top View> - When using DIP conversion board of 2.54mm pitch by cutting off a board. OCD/ Please connect CN1 and CN4 as following. CN1 CN4 Please short of RESET pad. CN4 CN1 CN4 CN1 1 GND 16 16 1 GND 1 N.C. GND 16 16 1 GND TOOL0 N.C. <.ottom View> RESET RESET TOOL0 <.ottom View> RESET T RESET RESET P122 P121 N.C. T RESET P122 P121 N.C. N.C. GND VDD N.C. X2 X1 VDD GND VDD X2 X1 8 9 SG-13-0556-01 9 VDD VDD 8 8 9 SG-13-0556-01 VDD 9 8 Please connect the following circuit according to use the P125/KR1/RESET pin. P125/KR1/RESET - When using RESET pin. - RESET Connect the external reset circuit. (Possible to be open) RESET ( ) - When using P125 or KR1 pin. - P125/KR1 Connect the circuit the P125/KR1. P125/KR1 R20UT2894XJ0100 Rev.1.00 Page 2 of 3 R20UT2894XJ0100 Rev.1.00 Page 2 of 3 2014.2.28 2014.2.28