RTK5RLG140C00000BJ Renesas

RL78/G14 Fast Prototyping Board Quick Start Guide The RL78/G14 Fast Prototyping Board provides an entry point for evaluation, prototyping and development with the RL78/G14 MCU. Moreover, since this board incorporates an emulator circuit, you can use it for designing your own applications without needing to make further investments in tools. This product includes through-holes for pin headers that allow access to all MCU signal pins, allowing easy prototyping with a breadboard. (1) Package components RL78/G14 Fast Prototyping Board (RTK5RLG140C00000BJ) Quick Start Guide (this document) (2) Table of board specifications Item Specification Evaluation MCU Part No.: R5F104MLAFB package: 80-pin LFQFP On-chip memory: 512-KB ROM, 48-KB RAM, 8-KB data flash memory Board size Size: 54 mm 95 mm thickness: 1.6 mm Power-supply voltage VDD: 1.8 V to 5.5 V EVDD is the same voltage as VDD. Power-supply circuit USB connector: VBUS (5-V input) VBUS is converted to 3.3 V by LDO. 2-pin external power-supply header*1 Coin-cell battery: CR2032 (3 V)*1 Push switch Reset switch x 1 user switch x 1 LED Power indicator: green x 1, user: green x 2, ACT LED: green x 1 USB connector Connector: Micro USB Type-B Pmod connector Connector: Angle type, 12 pins x 2 Arduino connector Connector: 6 pins x 1, 8 pins x 2, 10 pins x 1 The interface is compatible with Arduino UNO R3. MCU header *1 Header: 40 pins x 2 *1: This part is not mounted. Do not fit (DNF). (3) Parts layout Six analog pins TM for Arduino Uno R3 Eight power pins TM for Arduino Uno R3 ACT LED TM Pmod connector 1 Micro-USB MCU pin headers connector (41 to 80) RL78/G14 MCU Power LED Sub-clock oscillator User LEDs MCU pin headers (1 to 40) TM Pmod connector 2 User switch Ten digital pins TM for Arduino Reset switch Uno R3 Eight digital pins TM for Arduino Uno R3 (4) Arduino interface D15 P60 SCLA0 32 31 D14 P61 SDAA0 30 ADREF P20 AV REFP GND GND 29 NC 14 28 D13 P54 SCK31 SCL31 V IOREF 13 CC D12 P53 SI31 27 SDA31 RESET 12 26 D11 P52 SO31 3V3 11 25 D10 P12 TRDIOB1 SO11 5V 10 TRDIOC1 24 D9 P11 SI11 SDA11 GND GND 9 23 D8 P03 RxD1 GND GND 8 V VIN 7 CC 22 D7 P02 TxD1 21 D6 P10 TRDIOD1 SCK11 SCL11 ANI6 P26 A0 6 20 D5 P77 INT11 KR7 ANI5 P25 A1 5 19 D4 P76 INT10 KR6 ANI4 P24 A2 4 18 D3 P75 INT9 KR5 ANI3 P23 A3 3 17 D2 P142 SCK30 SCL30 ANI2 P22 A4 2 16 D1 P144 TxD3 SO30 ANI1 P21 A5 1 15 D0 P143 RxD3 SI30 SDA30 Pin no. Analog pin Power supply Digital pin GND PWM function Control signal Serial array unit Port Other function (5) PMOD interface The RL78/G14 Fast Prototyping Board has two Pmod connectors for the Type 2A interface. SPI (CSI) Pin no. Port UART I2C 1 P74 7 P140 2 P51 SO00 TxD0 8 P130 3 P50 SI00 RxD0 SDA00 9 P147 4 P30 SCK00 SCL00 10 P146 5 GND 11 GND *Note: These serial ports are different from 6 V CC those for the Pmod I2C interface 12 V CC recommended by Digilent. 1 P16 7 P141 2 P13 SO20 TxD2 8 P110 3 P14 SI20 RxD2 SDA20 SCLA0 9 P17 4 P15 SCK20 SCL20 SDAA0 10 P111 5 GND 11 GND 1 7 Pin no. Serial array unit 6 V CC 2 8 12 V Power supply CC Redirection of peripheral I/O 3 9 4 10 GND 5 11 Port 6 12 (6) Note on using the board Download the user s manual from the Web site below and check the full specifications before using the board. An integrated development environment and flash programming software are also available for downloading. URL: