DATA SHORT To request the full datasheet, please visit www.intersil.com/products/TW9900 TW9900 FN7767 Rev 5.00 Low Power NTSC/PAL/SECAM Video Decoder with VBI Slicer April 7, 2016 The TW9900 is a low power NTSC/PAL/SECAM video decoder Features chip that is designed for portable applications. It consumes less than 100mW in typical composite input applications. The Video Decoder available power-down mode further reduces the power NTSC (M, 4.43) and PAL (B, D, G, H, I, M, N, N combination), consumption. It uses the 1.8V for both analog and digital PAL (60), SECAM support with automatic format detection supply voltage and 3.3V for I/O power. A single 27MHz crystal is all that is needed to decode all analog video standards. Software selectable analog inputs allow any of the following combinations, e.g., 2 CVBS or 1 Y/C The video decoder decodes the baseband analog CVBS or S-video signals into digital 8-bit 4:2:2 YCbCr for output. It Built-in analog anti-alias filter consists of analog front-end with input source selection, Two 10-bit ADCs and analog clamping circuit variable gain amplifier and analog-to-digital converters, Y/C Fully programmable static gain or automatic gain control for separation circuit, multi-standard color decoder (PAL BGHI, the Y-channel PAL M, PAL N, combination PAL N, NTSC M, NTSC 4.43 and SECAM) and synchronization circuitry. The Y/C separation is Programmable white peak control for the Y-channel done with high quality adaptive 4H comb filter for reduced 4-H adaptive comb filter Y/C separation cross color and cross luminance. The advanced PAL delay line for color phase error correction synchronization processing circuitry can produce stable pictures for a non-standard signal as well as a weak signal. The Image enhancement with peaking and CTI output of the decoder is line-locked and formatted to the ITU-R Digital subcarrier PLL for accurate color decoding 656 output with embedded sync. Digital horizontal PLL for synchronization processing and The TW9900 also includes circuits to detect and process pixel sampling vertical blanking interval (VBI) signal. It slices and processes Advanced synchronization processing and sync detection for VBI data for output through video bus. Some information can handling nonstandard and weak signal also be alternatively retrieved through the host interface. It also detects copy-protected signal according to Macrovision Programmable hue, brightness, saturation, contrast, and standard including AGC and color stripe pulses. sharpness Automatic color control and color killer A 2-wire serial host interface is used to simplify system integration. All the functions can be controlled through this Chroma IF compensation interface. Detection of level of copy protection according to Macrovision standard ITU-R 601 or ITU-R 656 compatible YCbCr(4:2:2) output format VBI slicer supporting industrial standard data services VBI data pass through, raw ADC data output Programmable output cropping Miscellaneous Two-wire MPU serial bus interface Supports real time control interface Power save and power-down mode Typical power consumption <100mW Single 27MHz crystal for all standards Supports 24.54MHz and 29.5MHz crystal for high resolution square pixel format decoding 3.3V tolerant I/O 1.8V/3.3V power supply 32 Ld TQFP and 32 Ld QFN package FN7767 Rev 5.00 Page 1 of 2 April 7, 2016TW9900 Copyright Intersil Americas LLC 2012-2016. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil s sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN7767 Rev 5.00 Page 2 of 2 April 7, 2016