Datasheet Stepping Motor Driver series Micro step 36V Stepping Motor Drivers BD63524AEFV General Description Major Characteristics BD63524AEFV series are stepping motor drivers of 1/8 Range of power supply voltage 8 28 V micro step(Eighth step) drive. As for its basic function, it Rated output current 2.5 A is a low power consumption bipolar PWM constant Rated output current (peak) 3.0 A current-drive driver with power supply rated voltage of Range of operating temperature -25+85 36V and rated output current (DC) of 2.5A. The input Output ON resistance (total of upper 0.35 (Typ) interface is CLK-IN type. and lower resistors) There are step modes of Full step & Half step, Quarter step, Eighth step mode by internal DAC (D-A converter), Package W(Typ) x D(Typ)x H(Max) and for current decay mode, the ratio of FAST DECAY HTSSOP-B28 9.70mm x 6.40mm x 1.00mm & SLOW DECAY can be freely set, so the optimum control conditions for every motor can be realized. In addition, being able to drive with one system of power supply makes contribution to the set designs getting easy. Features 1) Single power supply input (rated voltage of 36V) 2) Rated output current:(DC) 2.5A 3) Low ON resistance DMOS output 4) CLK-IN drive mode 5) PWM constant current control (other oscillation) 6) Built-in spike noise cancel function (external noise filter is unnecessary) Basic application circuit 7) Full step, Half step, Quarter step, Eighth step drive GND 9 8) Timing free for changing step modes 9) Current decay mode switching function (linearly 15 CLK 14 PS variable FAST/SLOW DECAY ratio) CW CCW 16 10) Normal rotation & reverse rotation switching 18 MODE0 function MODE1 19 11) Power save function 20 ENABLE 12) Built-in logic input pull-down resistor 13) Power-on reset function VCC1 7 14) Thermal shutdown circuit (TSD) VREF 13 OUT1A 15) Over current protection circuit (OCP) 5 16) Under voltage lock out circuit (UVLO) 2 OUT1B 17) Over voltage lock out circuit (OVLO) 3 RNF1 18) Ghost Supply Prevention (protects against 4 malfunction when power supply is disconnected) RNF1S 19) Adjacent pins short protection VCC2 22 20) Inverted mounting protection OUT2A 21) Microminiature, ultra-thin and high heat-radiation CR 24 10 (exposed metal type) HTSSOP-B28 package 27 OUT2B 26 RNF2 Application MTH 12 25 PPC, multi-function printer, laser beam printer, and RNF2S TEST ink-jet printer 17 GND 1 Monitoring camera and WEB camera Sewing machine Photo printer, FAX, scanner and mini printer Figure 1. BD63524AEFV application circuit diagram Toy and robot Product structuresilicon monolithic integrated circuit It is not the radiation-proof design for this product. www .rohm.com TSZ02201-0P2P0B701510-1-2 2016 ROHM Co., Ltd. All rights reserved. 1/23 TSZ2211114001 12.Jul.2017 Rev.002 BD63524AEFV Terminals Configuration Diagram 28 GND NC 1 TSD OCP 15 CLK GND 16 OUT2B CW CCW 9 2 27 OVLO UVLO OUT1B 18 Translator MODE0 19 RESET MODE1 14 PS RNF1 3 26 RNF2 20 ENABLE RNF1S 4 25 RNF2S VREF 13 4bit DAC OUT1A 5 24 OUT2A VCC1 7 NC 6 23 NC OUT1A 5 RNF1S 2 OUT1B VCC1 7 22 VCC2 3 RNF1 RNF2S 4 RNF1S 21 NC 8 NC Blank time PWM control VCC2 22 GND 9 20 ENABLE OUT2A CR 24 10 OSC 27 OUT2B 19 MODE1 CR 10 26 Mix decay RNF2 MTH 12 control 25 NC 11 18 MODE0 TEST RNF2S 17 Regulator GND 1 MTH 12 17 TEST VREF 13 CW CCW 16 Figure 3. BD63524AEFV Block Diagram PS 14 15 CLK Figure 2. Terminals Configuration Diagram Descriptions on Terminals Pin No. Pin name Function Pin No. Pin name Function Clock input terminal for advancing the 1 GND Ground terminal 15 CLK electrical angle. 2 OUT1B H bridge output terminal 16 CW CCW Motor rotating direction setting terminal Connection terminal of resistor for Terminal for testing 3 RNF1 17 TEST1 output current detection (Used by connecting with GND) Input terminal of current limit Motor excitation mode setting terminal 4 RNF1S 18 MODE0 comparator H bridge output terminal Motor excitation mode setting terminal 5 OUT1A 19 MODE1 6 NC Non connection 20 ENABLE Output enable terminal 7 VCC1 Power supply terminal 21 NC Non connection Non connection Power supply terminal 8 NC 22 VCC2 Ground terminal Non connection 9 GND 23 NC Connection terminal of CR for setting H bridge output terminal 10 CR 24 OUT2A chopping frequency 11 NC Non connection 25 RNF2S Input terminal of current limit comparator Connection terminal of resistor for output 12 MTH Current decay mode setting terminal 26 RNF2 current detection 13 VREF Output current value setting terminal 27 OUT2B H bridge output terminal Power save terminal Non connection 14 PS 28 NC www .rohm.com TSZ02201-0P2P0B701510-1-2 2016 ROHM Co., Ltd. All rights reserved. 2/23 TSZ2211115001 12.Jul.2017 Rev.002 Control logic Predriver