Datasheet AC/DC Drivers PWM Control IC BM1P065FJ General Features The PWM control IC for AC/DC BM1P065FJ PWM frequency: 65 kHz provides an optimum system for all products that PWM current mode method include an electrical outlet. Frequency hopping function A built-in start circuit that withstands 650 V helps to Burst operation during light load / Frequency keep power consumption low. Both isolated and reduction function non-isolated versions are supported, making for 650 V start circuit simpler design of various types of low-power VCC pin undervoltage protection converters. Switching MOSFET and current detection VCC pin overvoltage protection resistors are external devices, thus achieving a higher CS pin open protection degree of freedom in power supply design. The CS pin Leading-Edge-Blanking function switching frequency is set as fixed. Since current mode Per-cycle overcurrent limiter function control is used, a current limit is imposed in each cycle, Overcurrent limiter with AC voltage compensation and excellent performance is demonstrated in function bandwidth and transient response. With a light load, Soft start function frequency is reduced and higher efficiency is realized. Secondary overcurrent protection circuit A frequency hopping function is also built in, contributing to low EMI. Also on chip are soft start and burst functions, a Package per-cycle overcurrent limiter, VCC overvoltage SOP-J8 4.90 mm 6.00 mm 1.65 mm pitch 1.27 mm protection, overload protection, and other protection (Typ.) (Typ.) (Typ.) (Typ.) functions. Basic Specifications Operating power supply voltage range: VCC 8.9 V to 26.0 V VH: to 600 V Applications Operating current: Normal: 0.60 mA (Typ.) AC adapters, TVs, and household appliances Burst mode: 0.35 mA (Typ.) (vacuum cleaners, humidifiers, air cleaners, air Oscillation frequency: BM1P065FJ: 65 kHz (Typ.) conditioners, IH cooking heaters, rice cookers, etc.) Operating temperature range: -40C to +85C Application circuit Line-up X-cap Frequency VCCOVP VCC recharge Brown-out discharge BM1P061FJ 65kHz Auto-restart BM1P062FJ 65kHz Latch BM1P063FJ 65kHz Auto-restart BM1P064FJ 65kHz Latch BM1P065FJ 65kHz Auto-restart BM1P066FJ 65kHz Latch BM1P067FJ 65kHz Auto-restart BM1P068FJ 65kHz Latch BM1P101FJ 100kHz Auto-restart BM1P102FJ 100kHz Latch BM1P103FJ 100kHz Auto-restart BM1P104FJ 100kHz Latch BM1P105FJ 100kHz Auto-restart BM1P106FJ 100kHz Latch BM1P107FJ 100kHz Auto-restart BM1P108FJ 100kHz Latch Figure 1Application Circuit Product structureSilicon monolithic integrated circuit This product is not designed for protection against radioactive rays . www.rohm.com TSZ02201-0F2F0A200170-1-2 2013 ROHM Co., Ltd. All rights reserved. 1/27 2.Oct.2013.Rev.001 TSZ2211114001 DatasheetDatasheet BM1P065FJ Absolute Maximum Ratings (Ta = 25C) Parameter Symbol Rating Unit Conditions Maximum voltage 1 Vmax1 -0.3 ~ 30.0 V VCC Maximum voltage 2 Vmax2 -0.3 ~ 6.5 V CS, FB, ACMONI Maximum voltage 3 Vmax3 -0.3 ~ 15.0 V OUT Maximum voltage 4 Vmax4 -0.3 ~ 650 V VH OUT pin peak current I 1.0 A OUT Allowable dissipation Pd 674.9 (Note1) mW When mounted o Operating temperature range Topr -40 ~ +85 C o Storage temperature range Tstr -55 ~ +150 C (Note1) SOP-J8: When mounted, 70 70 1.6 mm (glass epoxy on single-layer substrate). Reduce to 5.40 mW/C when used at Ta = 25C or above. Recommended Operating Conditions (Ta = 25C) Parameter Symbol Rating Unit Conditions Supply voltage range 1 VCC 8.9 ~ 26.0 V VCC pin voltage Supply voltage range 2 VH 80 ~ 600 V VH pin voltage Electrical Characteristics (Unless otherwise noted, Ta = 25C, VCC = 15 V) Rating Parameter Symbol Unit Conditions Min. Typ. Max. Circuit current FB = 2.0 V Circuit current (ON) 1 I - 600 1000 A ON1 (during pulse operation) FB = 0.0 V Circuit current (ON) 2 I - 350 450 A ON2 (during burst operation) VCC pin (5 pin) protection function VCC UVLO voltage 1 V 12.50 13.50 14.50 V VCC rise UVLO1 VCC UVLO voltage 2 V 7.50 8.20 8.90 V VCC drop UVLO2 VCC UVLO hysteresis V - 5.30 - V V V V UVLO3 UVLO3 = UVLO1- UVLO2 VCC OVP voltage 1 V 26.00 27.50 29.00 V VCC rise OVP1 VCC OVP voltage 2 V - 23.50 - V VCC drop OVP2 VCC OVP hysteresis V - 4.00 - V OVP3 Output driver block OUT pin H voltage V 10.5 12.5 14.5 V IO = -20 mA OUTH OUT pin L voltage V - - 1.00 V IO = +20 mA OUTL OUT pin pull-down resistance R 75 100 125 k PDOUT ACMONI detection circuit ACMONI detection voltage1 V 0.92 1.00 1.08 V ACMONI rises ACMONI1 ACMONI detection voltage2 V 0.63 0.70 0.77 V ACMONI falls ACMONI2 ACMONI Hysteresis V 0.20 0.30 0.40 V ACMONI3 ACMONI Timer T 180 256 330 ms ACMONI1 Start circuit block Start current 1 I 0.400 0.700 1.000 mA VCC = 0 V START1 Start current 2 I 1.000 3.000 5.000 mA VCC = 10 V START2 Inflow current from VH pin OFF current I - 10 20 uA START3 after release of UVLO Start current switching voltage V 0.400 0.800 1.400 V SC www.rohm.com TSZ02201-0F2F0A200170-1-2 2013 ROHM Co., Ltd. All rights reserved. 2/27 2.Oct.2013.Rev.001 TSZ2211115001