IDSS-03-S-04.00 Samtec

SLIM BODY FLAT RIBBON IDC CABLES (2.54 mm) .100 PITCH IDSS/IDSD/IDMS/IDMD SERIES IDSS/IDMS/IDMD ROW OPTION NO. PINS PER ROW SERIES Mates: - - TSW, MTSW, TSM, EJH, PHT, HMTSW, HTSW, HW, DW, EW, ZW, MTLW IDM S 02 thru 32 = Standard Tail Male Plug = Single = IDMS/IDMD IDSD IDS D 02 thru 36 Mates: = Socket = Double = IDSS/IDSD TST, HTST, ZST, BST, EJH (Color coded cable Not available for 31 thru 36 pins/row. See G option.) SPECIFICATIONS Insulator Material: Black Glass Filled Polyester DOUBLE Full size (64 positions): (82.55) 3.250 Contact (IDSS/IDSD): IDMS IDMD Less than 64 positions: No. Positions/row X (2.54) .100 + (1.68) .066 BeCu (Single) (Double) SINGLE Terminal (IDMS/IDMD): Full size (32 positions): (81.53) 3.210 (2.54) (5.08) Phosphor Bronze Less than 32 positions: No. Positions/row X (2.54) .100 + (0.71) .028 .100 .200 Plating: Au over 50 (1.27 m) Ni or Sn over 100 (2.54 m) Cu or 50 (1.27 m) Ni Wire: 28 AWG 7/36 stranded Tinned Copper Current Rating (IDSD/TST): 3.4 A per pin (For square or long tail see HCMX Series) (2 pins powered) Current Rating (IDMD): IDMX shown 3 A per pin (2 pins powered) Temperature Range: -20 C to +105 C (Rainbow Cable) DOUBLE IDSS IDSD -40 C to +105 C Full size (72 positions): (92.71) 3.650 (Single) (Double) Less than 72 positions: No. Positions/row x (2.54) .100 + (1.50) .059 (Gray Cable) Voltage Rating: SINGLE Full size (36 positions): (91.69) 3.610 425 VAC/600 VDC (5.08) (2.54) Less than 36 positions: No. Positions/row x (2.54) .100 + (0.48) .019 .200 .100 Lead Size Range: (0.56 mm) .022 SQ to (0.71 mm) .028 SQ Lead Insertion Depth: (9.27) (5.59 mm) .220 to .365 (6.22 mm) .245 REF IDSX shown ALSO AVAILABLE Molded-To-Position IDC Assembles Low Profile Skinny side locks Dual beam contacts Single and double row (6.35mm) .025 square and (5,84mm) .230 length tail available Visit samtec.com HCSD, samtec.com HCSS, samtec.com HCMD or samtec.com HCMS for more detailed information. Double End (D) Transfer End (T) Single End (S) Note: This Series is non-standard, non-returnable. F-221 samtec.com IDSS, samtec.com IDSD, samtec.com IDMS or samtec.com IDMD Unless otherwise approved in writing by Samtec, all parts and components are designed and built according to Samtecs specifications which are subject to change without notice.END ASSEMBLY ASSEMBLED LENGHTH OPTION - - - S XX.XX T B XX = Single End = Assembled Length = Tin Plating = Breakout (Socket or Male Plug on one end) (Both Ends) (Specify XX as number of conductors to be broken out) (Breakout starts with Number 1 lead D C indicated by brown wire or red stripe. = Double End = Tin IDM, Shown on top side) (Socket or Male Plug on each end) 10 (0.25 m) Gold IDS (-T End Assembly Required) RW T = Reversed Wiring = Transfer End A ( 1 wire opposite position 1) (Male Plug on one end with socket on other. = Tin IDS, Begin part number with IDM) 10(0.25 m) Gold IDM (-T End Assembly Required) S XX = Daisy Chain, Single (When mating double row P XX connector with two single row =Polarized connectors, the outer most single will Specify XX as position. be connected to Conductor 1 and For Double the same position the inside single to Conductor 2) will be polarized on both ends. (Not available on IDM unless transfer, then only the socket is polarized.) D XX = Daisy Chain, Double G = Gray Cable W XX Specify G for Gray cable. = Wiring Reverse Daisy Chain, Single Gray cable has one red edge. (Same as S XX except outer strip IDSS and IDMS uses connected to Conductor 2 and inside Assembled Length in (2.54 mm) .100 centerline cable. strip connected to Conductor 1) 1 INCHES ( /8 ) IDSD and IDMD uses (2 inches minimum) (1.27 mm) .050 centerline cable. 72 04 02 R Cable is 28 AWG 7/36 copper wire. = Reverse Standard cable is same as above except color M = Middle Reverse 71 03 01 ST X (Requires SXX, WXX or DXX) = Stripped & Tinned Assembled Length (XX.XX) Polarized (P XX) (Specify Sufx ffi rom table) 1 O (All dimensions are /16 (1.59 mm) = Outside Reverse (Not available in 28 positions and higher) (Requires SXX, WXX or DXX) 2 1 XX 8 min. Double Row Connectors (IDSD or IDMD) XX Outer Most 1 ST8 /8 (3.18) 5 max. 1 2 min. ST4 /4 (6.35) 4 minimum Breakout starts with 1 ST2 /2 (12.70) Number 1 lead indicated Daisy Chain SIngle (S XX) by brown wire or red stripe. 3 ST3 /8 (9.53) Shown on top side. Stripped & Tinned (ST X) Breakout (B X) Reverse (R) Middle Reverse (M) Outside Reverse (O) F-221 samtec.com IDSS, samtec.com IDSD, samtec.com IDMS or samtec.com IDMD Unless otherwise approved in writing by Samtec, all parts and components are designed and built according to Samtecs specifications which are subject to change without notice.