HS25 Incremental Optical Encoder Mechanical Specifications Shaft Bore: 0.375, 0.750, 0.625, 0.500, dia. 0.625 and under are supplied with insulating sleeves. Allowable Misalignment: 0.005: T.I.R. on mating shaft 0.75 from shaft end Bore Runout: 0.001 T.I.R. The HS25 combines the Starting Torque at 25 C: Through shaft version (SS) = 7 in-oz (max) rugged, heavy-duty features Blind shaft version (BS) = 4 in-oz (max) Bearings: 52100 SAE high carbon steel usually associated with Shaft Material: 6061-T6 aluminum alloy shafted encoders into a Bearing Housing: Die cast aluminum with protective finish hollow-shaft style. Its design Cover: Die cast aluminum with protective finish 9 Bearing Life: 7.5 X 10 revs (25,000 hrs at 2500 RPM) includes dual bearings and Maximum RPM: 6,000 RPM (see Frequency Response, below) shaft seals for NEMA 4, 13 4 2 Moment of Inertia: 17 X 10 oz-in-sec and IP65 environmental Weight: 9 oz typical ratings, a rugged metal Electrical Specifications housing, and a cable gland. Code: Incremental Output Format: 2 channels in quadrature, 1/2 cycle index gated This low-profile design, with negative B channel just 2 deep, is easily mounted on a through shaft. Securing the encoder to the shaft Cycles per Shaft Turn: up to 2048 (see table A, this page) is simple with a collet-style single screw clamp. The optional anti-rotation tether block Supply Voltage: 5 to 28 VDC available (see note 5) Current Requirements: 100 mA typical + output load, 250 mA (max) maintains housing stability during operation. The HS25 is designed to accommodate Voltage/Output: (see note 5) shafts up to 3/4 in diameter. With optional insulating inserts, it can be mounted on 15V/V: Line Driver, 515 VDC in, V = V out in smaller diameter shafts. Applications include motor feedback and vector control, paper 28V/V: Line Driver, 528 VDC in, Vout = Vin 28V/5: Line Driver, 528 VDC in, V = 5 VDC out converting and printing industries, robotic control, web process control along with many 28V/OC: Open Collector, 528 VDC in, OC out other applications. Protection Level: Reverse, overvoltage and output short circuit Frequency Response: 100 kHz (see note 7) Output Terminations: (see table 1, back page) Special Models of the HS25 Incremental Encoder are available with one or more of the fol- Note: Consult factory for other electrical options lowing certifications. Consult factory for details. Environmental Specifications Enclosure rating: NEMA 4 & 13 (IP65) when ordered with shaft seal U.S. Standards Class I, Group A,B,C & D EN 55011 and a cable gland. Class II Group E, F & G and EN 61000-6-2 Temperature: Operating, 0 to 70C extended temperature testing up to 85C available (see note 8) Storage, -25 to 90 C unless extended tem- Canadian Standards UL 12.0035X perature option called out C Class I, Zone 0, Group IIC UL 13.0071X Shock: 50 gs for 11 msec duration Vibration: 5 to 2000 Hz 20 gs CENELEC Humidity: 98% RH non-condensing Class I, Div 2, Group A,B,C & D II 1 G Ex ia IIB/IIC T4 NOTES & TABLES: All notes and tables referred to in the text can be found Class II, Div 2, Group F & G II 3 G Ex nA IIB T4 Gc on the back of this page. HS25 Incremental Ordering Options FOR ASSISTANCE CALL 800-350-2727 Use this diagram, working from left to right to construct your model number (example: HS25F-62-R1-SS-1024-ABZC-28V/V-SCS18). All notes and tables referred to can be found on the back of this page. HS25 TYPE: SPECIAL NO. OF CHANNELS: HAZARDOUS SHAFT BORE: SHAFT SEAL VOLTAGE/OUTPUT: HS = Hollow Shaft FEATURES: A = Single Channel AREA RATINGS: CONFIGURATION: 28V/V = 528V 75 = 0.750 in/out 25 = 2.5 Encoder S = Special Blank = None AB = Dual Quad. Ch. SS = Through Shaft Rubber Seals 28V/5 = 528V /5V 62 = 0.625 in out Diameter EX = Intrinsically Safe features specified BS = Blind Shaft Rubber Seal ABZ = Dual with Index 28V/OC = 528V /OC in out 50 = 0.50 NI = Non-Incendive on purchase order FS = Through Shaft Felt Seals AZ = Single with Index See note 5 37 = 0.375 Contact factory for (consult factory) BFS = Blind Shaft Felt Seal See note 3 voltage options See note 6 See note 2 TETHER: HOUSING CONFIG: X = COMPLEMENTS: CYCLES PER Blank = None OUTPUT TERMINATION: F = Standard Express TURN: C = Complementary R1 = Tether Block SM12 = MS3112E12-10P Encoder (Enter Cycles) Outputs SCS = Shielded, Jacketed Cable with Cable and Pin See table A See note 4 R2 = Tether Arm gland seal and cable length in inches, (i.e. SCS18 = 18 inches) SCS18-M18 = SM18 connector on end of cable EXPRESS ENCODERS Items highlighted with are standard Express Encoders and ship in one to three days. with length specified in inches (i.e. SCS18-M18) M18 = MS3101F18-1P See table 1 and note 9 Specification No. 02065-001 Rev.5-16 These commodities, technology or software if exported from the United States must be in accordance with the Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.HS25 Incremental Optical Encoder Dimensions Notes 1. The typical hollow shaft product is supported by, and clamped to, the driving Thru Shaft Version shaft. A flexible tether is used to keep the housing from rotating. 2. The rubber shaft seal is recommended in virtually all installations. The most common exceptions are applications requiring a very low starting torque or those requiring operation at both high temperature and high speed. For these excep- tions, a felt shaft seal is recommended. Felt seals require very low starting torque and can virtually eliminate frictional heat. Encoders ordered with felt shaft seals will have an enclosure rating of IP50 and will have less than 1/10th the Starting Torque specified under Mechanical Configurations. 3. Non-standard index widths and multiple indices are available by special order. Consult factory. 4. Complementary outputs are recommended for use with line driver type (source/sink) outputs. When used with differential receivers, this combination provides a high degree of noise immunity. 5. Output ICs: Output ICs are available as either Line Driver (LD) or NPN Open Collector (OC) types. Open Collectors require pull-up resistors, resulting in higher R1 Tether Block Blind output source impedance (sink impedance is similar to that of line drivers). In and Pin Shaft general, use of a Line Driver style output is recommended. Line Drivers source or Version sink current and their lower impedance mean better noise immunity and faster switching times. Warning: Do not connect any line driver outputs directly to circuit common/OV, which may damage the driver. Unused outputs should be isolated and left floating. Our applications specialists would be pleased to discuss your system requirements and the compatibility of your receiving electronics with Line TOLERANCES: .XX=0.01, .XXX=0.005 Driver type outputs. 28V/V: Multi-voltage Line Driver (7272*): 100 mA source/sink. Input voltage 5 to 28 VDC +/- 5% standard (Note: V = V ). This driver is TTL compatible when M12 out in R2 Tether Arm used with 5 volt supply. Supply lines are protected against overvoltage to 60 volts and reverse voltage. Outputs are short circuit protected for one minute. Supply current is 120 mA typical (plus load current). This is the recommended replace- ment for 3904R and 7406R open collector outputs with internal pullup resistors. It is also a direct replacement for any 4469, 88C30, 8830 or 26LS31 line driver 28V/5: Multi-voltage Line Driver (7272*): 100 mA source/sink. Input voltage 5 to 28 VDC +/- 5% standard, internally regulated with 5V (TTL compatible) logic out. Supply lines are protected against overvoltage to 60 volts and reverse voltage. Outputs are short circuit protected for one minute. Supply current is 90 mA typical (plus load cur- rent). 15V/V: Multi-voltage Line Driver (4469*): 100 mA source/sink. Input voltage 5 to 15 VDC +/- 5% standard (Note: V = V ). TTL compatible when used with 5 out in volt supply. Supply lines are protected against overvoltage to 60 volts and reverse voltage. Outputs are short circuit protected for one minute. Supply current is 90 mA typical (plus load current). This is a direct replacement for the 4469 Line Driver. Table A Table 1 28V/OC: NPN Open Collector (3904*, 7273*). Current sink of 80 mA max. Current M18 CONNECTOR M12 CONNECTOR sourced by external pull- up resistor. Output can be pulled up to voltage other than PIN CHANNEL PIN CHANNEL HS25 Disc Resolutions Incremental Output + A A supply voltage (30 V max). Input voltage 5 to 28 VDC /- 5% standard. Supply A A 10 12 60 88 100 122 250 360 Terminations B B B B current is 120 mA typical. This replaces prior ICs with designations of 3904, 7406, C Z C Z 500 512 1000 1024 2000 2048 3302, 681 and 689. 5V/OCR, 15V/OCR, 24V/OCR: Open Collector (3904R*, The connector style will D +V D +V 7406R*, 7273R*): Current sink of 70 mA max. Includes internal pull-ups sized determine pinouts. For Other resolutions availableconsult factory. E E at approximately 100 ohms/volt. Max current source is 10 mA. Supply current example, an encoder F 0V F 0V is 100 mA typical, 120 mA with internal pull-ups. The 5V/OCR, 15V/OCR and with ABC channels and G CG G CG Figure 1 24V/OCR are often replaced by the 28V/V in system upgrades. an M18 connector uses H A H A Output Waveform I B J B 3904, 3904R, 4469, 5V/V, 5V/OC, 5V/OCR, 9V/OC: Intrinsically safe line the table to the right. J Z K Z driver and open collector outputs. These drivers are specific to intrinsically safe M14 CONNECTOR M16 CONNECTOR CHANNELS DESIGNATED IN MODEL NO. encoders, and are installed per the appropriate control drawings listed in Table PIN PIN ABZ ABC 2.1 on page 48. HI E A A A 6. Special S at the end of the model number is used to define a variety of non- D B B B LO standard features such as special shaft lengths, voltage options, or special testing. C C Z A Please consult the factory to discuss your special requirements. B D +V (SUPPLY VOLTAGE) F E B 7. Higher frequency response may be available. Please consult with the factory. A F 0 V (CIRCUIT COMMON) 8. Extended temperature ratings are available in the following ranges: G CASE GROUND (CG) (except H20) -40 to 70C, -40 to 85C, 20 to 105C and 40 to 105C depending on CHANNELS DESIGNATED IN MODEL NO. WIRE COLOR DA 15P the particular model. Some models can operate down to -55C. Extended (22AWG) CONNECTOR ABZ ABC ABZC YEL 13 A A A temperature ranges can affect other performance factors. Consult with factory BLUE 14 B B B for more specific information. ORN 15 Z Z 9. Mating straight plug receptacles may be ordered from the factory: W-Yel 10 A A W-Blu 11 B B For M12 use MS3116F12-10S, For M14 use MS3106F14S-6S W-Orn 12 Z For M14/19 use MS3116J14-19S, For M16 use MS3106F16S-1S RED 6 +V (SUPPLY VOLTAGE) CCW Rotation Viewing Face For M18 use MS3106F18-1S, For M20 use MS3106F20-29S BLK 1 0 V (CIRCUIT COMMON) GRN 9 CASE GROUND (CG) (except H20) WHITE SHIELD DRAIN (Shielded Cable Only) Tel: 805-716-0322/800-350-2727 1461 Lawrence Dr, Thousand Oaks, CA 91320 www.beisensors.com