OMNICODER PROGRAMMING TOOL PN 60031-101 Introduction The Omnicoder programming tool is designed to make the re-programming of the Omnicoder Encoder as simple as possible. It is powered by the USB port of a laptop computer and uses a special data cable to transfer the new resolution to the encoder. Omnicoders come from the factory pre-programmed with a resolution of 1024 counts per turn and can be changed to any whole number value from 1 to 10,000. Changing the resolution only takes a matter of a few seconds once the Omnicoder is attached to the computer. Features Easy set-up and installation of software Simple, visual connection verification Encoder comes pre-tested and programmed at 1024 cpt Just type in your new resolution and click the program button Straightforward and fast reprogramming. Applications Installations with frequent adjustments or set-ups like printing or packaging Plant maintenance where you don t know which encoder resolution to stock for repairs. With the Omnicoder you just stock one and program it as needed. As a way to do electronic line shafting, especially when you have an unusual ratio between shafts, like 5:8 for example. INSTALLATION AND PROGRAMMING Installing the USB Driver and Software Step 1 Go to No encoder detected No cable detected Program new resolution Program Programming the Omnicoder Step 9 Using the Omnicoder programming cable (60031-101), plug the USB connector end into your PC. The red X (No cable detected) should change to a green check mark, indicating that the USB Programming Module was detected. (This may take up to 15 seconds) Step 10 Plug the M18 connector end into the Omnicoder unit. The red X (No encoder detected) should change to a green check mark, and the current Omnicoder resolution will be displayed on your computer screen. Step 11 To change the Omnicoder resolution, enter a new resolution as an integer between 1 and 10000 in the box labeled Program New Resolution. Then click the Program button. In a few seconds, the new resolution will be uploaded to the Omnicoder . The Omnicoder is now programmed and can be disconnected. To program a new resolution, repeat Steps 9-11 Page 2 Sensata Technologies, Inc. (Sensata) data sheets are solely intended to assist designers (Buyers) who are developing systems that CONTACT US incorporate Sensata products (also referred to herein as components). Buyer understands and agrees that Buyer remains responsible for using its independent analysis, evaluation and judgment in designing Buyers systems and products. Sensata data sheets have Americas been created using standard laboratory conditions and engineering practices. Sensata has not conducted any testing other than that +1 (800) 350 2727 Option 1 specifically described in the published documentation for a particular data sheet. Sensata may make corrections, enhancements, sales.beisensors sensata.com improvements and other changes to its data sheets or components without notice. Europe, Middle East & Africa Buyers are authorized to use Sensata data sheets with the Sensata component(s) identified in each particular data sheet. HOWEVER, NO +33 (3) 88 20 8080 OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER SENSATA INTELLECTUAL PROPERTY RIGHT, AND position-info.eu sensata.com NO LICENSE TO ANY THIRD PARTY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT, IS GRANTED HEREIN. SENSATA DATA SHEETS Asia Pacific ARE PROVIDED AS IS. SENSATA MAKES NO WARRANTIES OR REPRESENTATIONS WITH REGARD TO THE DATA SHEETS OR USE sales.isasia list.sensata.com OF THE DATA SHEETS, EXPRESS, IMPLIED OR STATUTORY, INCLUDING ACCURACY OR COMPLETENESS. SENSATA DISCLAIMS China +86 (21) 2306 1500 ANY WARRANTY OF TITLE AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET Japan +81 (45) 277 7117 ENJOYMENT, QUIET POSSESSION, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS WITH REGARD Korea +82 (31) 601 2004 TO SENSATA DATA SHEETS OR USE THEREOF. India +91 (80) 67920890 All products are sold subject to Sensatas terms and conditions of sale supplied at www.sensata.com SENSATA ASSUMES NO LIABILITY Rest of Asia +886 (2) 27602006 FOR APPLICATIONS ASSISTANCE OR THE DESIGN OF BUYERS PRODUCTS. BUYER ACKNOWLEDGES AND AGREES THAT IT IS SOLELY ext 2808 RESPONSIBLE FOR COMPLIANCE WITH ALL LEGAL, REGULATORY AND SAFETY-RELATED REQUIREMENTS CONCERNING ITS PRODUCTS, AND ANY USE OF SENSATA COMPONENTS IN ITS APPLICATIONS, NOTWITHSTANDING ANY APPLICATIONS-RELATED INFORMATION OR SUPPORT THAT MAY BE PROVIDED BY SENSATA. Mailing Address: Sensata Technologies, Inc., 529 Pleasant Street, Attleboro, MA 02703, USA. Spec. Sheet No. 02324-001 Rev:04/11/19 www.sensata.com Copyright 2019 Sensata Technologies, Inc.