9360 Series Dual Output Hall Effect Rotary Position Sensor The BEI Sensors 9360 Series rotary sensor is a non-contacting Hall effect device with up to 360 of rotation and dual outputs. This rugged design is ideally suited for continuous rotation applications where reliability and durability are a priority. The sensor provides absolute position at power on and offers two completely isolated outputs. The packaging is similar to other BEI devices and meets the severe durability requirements that are typical in off-highway and agriculture environments. This combination of magnet, sensor and sealed packaging offers excellent temperature stability and corrosion resistance. The sensor can be configured for Analog (voltage) or PWM output. These programmability features are configured at the factory and allow for greater flexibility in creating custom limited electrical angle outputs (i.e.20 degrees for full scale) with short turnaround times. Fully sealed, (meeting and/or exceeding IP67 and IP69K standards) the 9360 is resistant to contamination and moisture. An integrally molded 6-pin Metri-Pack or Ampseal connector makes a sealed connection with industry standard mating connectors. Mechanical Specifications Electrical Specifications Environmental Specifications Range: 0 to 360 with no stops/no spring, Active Electrical Angle: 15 to 360 in 15 Sealing: IP67 and IP69K per DIN 40050-9 allowing for continuous rotations* increments (no spring option). 15 to 165 Vibration: 10G peak, 20 - 2,000 Hz Spring/Rotor Return Direction Options: 0 to 180 increments (spring option) Humidity: 95% RH 40 C with spring return options 1 & 2 0 to 360 with Input Voltage: 5.0 V0.25V DC Liquid Exposure: Salt water, cola, motor oil, no spring option 3 (other, custom limited angles Overvoltage Protection: 20V ethylene glycol, paint, diesel fuel ranges available) Reverse Polarity Protection: Yes RoHS: Yes Mounting: 2 x 4.5mm on 32mm centers Short Circuit Protection: 10VDC Operating temperature range: -40C to +125C Shaft: 6mm with 4.6mm flat Output Signal: 5% to 95% Analog Ratiometric/ Storage temperature range: -40C to +125C Termination: Metri-Pack or Ampseal PWM* Shock: 50Gs, half since pulse, 5 msec duration Housing: Glass filled PBT (Polybutylene Resolution: 12 Bit terephthalate) Accuracy: 0.6% of full scale at room temperature Life: 35 M cycles 1 M cycles w/1kg side load 0.9% of full scale over operating temperature Frequency response: 1 kHz minimum range Rotational torque: 0.025 - 0.110 N-m EMC: 100 V/m (14 kHz-1 GHz range) Weight: 35 grams (approx.) ESD: 8kV Input current: 18mA maximum per output 36mA maximum total (both channels) *Different outputs and mechanical range(s) available Product Features Factory programming through connector: Allows for Fully programmable: The standard sensor provides quick turn-around on custom electrical angles 15-360 electrical degrees. Multiple outputs with Sealed construction: IP66 / IP67, 6-pin I/O interface to limited electrical angles up to 360 and temperature Packard Electric Metri-Pack Pull-to-Seat 150.2 Series compensation are also available P/N 12162261 or P/N 12162260 connector Ampseal 16 Compression molded Neodymium magnets: Provide - 6 position, P/N 776433-1sealed receptacle housings excellent temperature stability and corrosion resistance 2-Row Ratiometric analog output or PWM output: Reduced Temperature range: -40 to +125C standard sensitivity to voltage changes Operating life: 35M cycles Over one million cycles at 1kg side load 9360 Series Ordering Options for assistance, call 800.350.2727 Use this diagram, working from left to right to construct your model number 9360 Termination: Standard Electrical Angles: Spring/Rotor Return Direction: Blank= Metri-Pack 030 = +/- 15 060 = +/-30 090= +/- 45 etc. up to 1= Counter Clockwise Spring Return A= Ampseal 16 - 6 position 360 = +/- 180 2= Clockwise Spring Return NOTE: Other angles available, consult factory 3= No Spring, Continuous Rotation *Spring return: available for active electrical angles 15 to 165 only These commodities, technology or software if exported from the United States must be in accordance with the Spec.No.: 9360-100-1 www.beisensors.com Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S. law is prohibited. Rev D 2-2-16 Page 1/29360 Series Dual Output Hall Effect Rotary Position Sensor Dimensions- MetriPack connector (9360 Option) Output Examples Metric (+) (-) 1 ( ) Connector Pin Outputs 1 METRI-PACK AMPSEAL SENSOR 1 SENSOR 2 SENSOR 1 SENSOR 2 F B F BC Vs OUTPUT C D E B E A D A GROUND NOTES: TOLERANCES, UNLESS OTHERWISE NOTED: x.x= +/- 0.3 SPRING RETURN DIRECTION x.xx= +/- 0.13 SHAFT FLAT IS SHOWN WITH SENSOR AT 50%3% 1 VOLTAGE (INDEX) Dimensions- Ampseal connector (Option 9360A) These commodities, technology or software if exported from the United States must be in accordance with the Spec.No.: 9360-100-1 www.beisensors.com Bureau of Industry, and Security, Export Administration regulations. Diversion contrary to U.S. law is prohibited. Rev D 2-2-16 Page 2/2