MCMX60D5 Sensata

PCB Mount DataSheet MCMX Series SIP SSR Ratings to 5A 60 VDC, 10A 60 VDC and 6A 100 VDC MOSFET output DC control Low on-state impedance PRODUCT SELECTION Control Voltage 5 A 6 A 10 A 3-10 VDC MCMX60D5 MCMX100D6 MCMX60D10 (1)(3) OUTPUT SPECIFICATIONS Description Operating Voltage VDC 0-60 0-100 0-60 Maximum Off-State Leakage Current Rated Voltage Adc 100 100 100 (4) Maximum Load Current Arms 5 6 10 Minimum Load Current mArms 2 2 2 Maximum On-State Resistence Ohm (2) .10 .040 .018 60 100 100 Maximum Surge Current (10msec) Apk Maximum On-State Voltage Drop Rated Current VDC 0.5 0.24 0.18 (1) INPUT SPECIFICATIONS Description Control Voltage Range 3.0-10.0 VDC Must Turn On Voltage 3.0 VDC Must Turn Off Voltage 1.0 VDC Typical Input Current 5 VDC 15 mAdc Nominal Input Impedance 300 Ohm Maximum Turn-On Time msec 1.0 Maximum Turn-Off Time sec 300 GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) (2) 2500 Vrms 9 Minimum Insulation Resistance ( 500 VDC) (2) 10 Ohms Maximum Capacitance, Input/Output 15 pF Ambient Operating Temperature Range -40C to 80C Ambient Storage Temperature Range -40C to 125C Weight (typical) 0.7 oz. (20g) Encapsulation Thermally Conductive Epoxy Enclosure and PCB Meets the requirements of IEC60335-1 GENERAL NOTES 1) All parameters at 25C unless otherwise noted. 2) Dielectric and insulation resistance are measured between input and output. 3) Inductive loads should be diode suppressed. 4) At 55 Vdc. Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.PCB Mount DataSheet THERMAL DERATE INFORMATION MCMX60D10 MCMX100D6 MCMX60D5 10 9 8 7 6 5 4 3 2 1 0 20 30 40 50 60 70 80 AMBIENT TEMPERATURE (C) MECHANICAL SPECIFICATIONS Tolerances: 0.02 in / 0.5 mm All dimensions are in: inches millimeters BOTTOM VIEW 1 draft top to base 1.00 (25.4) .25 TYP. (6.35) 1 2 3 4 .16 .015 .20 .040 (1.0) DIA. (4.1)0.4 (5.1) .40 4 PLACES .70 (10.2) (17.8) PIN 1: +DC LOAD 1.10 .30 PIN 2: -DC LOAD (27.9) (7.6) PIN 3: +DC CONTROL 1.70 PIN 4: -DC CONTROL (43.1) AGENCY APPROVALS Agency Approvals IEC60335-1: Resistance to heat and fire meets the requirements of section 30, evaluated by TUV SUD. Glow Wire Test, per requirements of IEC/EN 60695-2-10 and IEC/EN 60695-2-11 Ball Pressure Test, per requirements of IEC/EN 60695-10-2 E116950 (6 and 10 A Models Only) Rev. 102416 Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice. LOAD CURRENT (AMPS)