TD2410-B Sensata

Panel Mount DataSheet T Series Triac output SSRs Output rated from 10A to 25A 24-240 VAC AC or DC control Zero-crossing (resistive loads) output PRODUCT SELECTION Control Voltage 10 A 25 A 3-32 VDC TD1210 TD1225 90-280 VAC TA1210 TA1225 3-32 VDC TD2410 TD2425 90-280 VAC TA2410 TA2425 AVAILABLE OPTIONS Output Voltage 12: 24-140 VAC 24: 24-280 VAC TD 24 25 Control Voltage Output Current TA: 90-280 VAC 10: 10 Amps TD: 3-32 VDC 25: 25 Amps Required for valid part number (1) OUTPUT SPECIFICATIONS Description 10 A 25 A 10 A 25 A Operating Voltage Range (47-63Hz) Vrms 24-140 24-140 24-280 24-280 Transient Overvoltage Vpk 400 400 600 600 Maximum Off-State Leakage Current Rated Voltage mArms 8 8 10 10 Minimum Off-State dv/dt Maximum Rated Voltage V/sec (3) 200 200 200 200 Maximum Load Current Arms 10 25 10 25 Minimum Load Current Arms 40 40 40 40 Maximum Surge Non-Repetitive (16.6ms) Apk 120 250 120 250 Maximum On-State Voltage Drop Rated Current Vpk 1.6 1.6 1.6 1.6 Maximum I t for Fusing (8.33 msec) A sec 1.48 1.02 1.48 1.02 Maximum Thermal Resistance Junction to Ceramic Base 60 260 60 260 Minimum Power Factor (with Maximum Load) 0.5 0.5 0.5 0.5 Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.Panel Mount DataSheet (1) INPUT SPECIFICATIONS Description TDxxxx TAxxxx Control Voltage Range 3-32 VDC 90-280 VAC Minimum Turn-On Voltage 3.0 VDC 90 VAC Minimum Turn-Off Voltage 1.0 VDC 10 VAC Maximum Reverse Voltage -32 VDC - Typical Input Current 3.4 mA 5 VDC, 20 mA 28 VDC 2 mA 120 Vrms, 4 mA 240 Vrms Nominal Input Impedance 1500 Ohm 60 K Ohm Maximum Turn-On Time msec 1/2 Cycle 10 1/2 Cycle 40 Maximum Turn-Off Time msec (1) GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) 4000 Vrms 9 10 Ohm Minimum Insulation Resistance ( 500 V DC) Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -40 to 80 C Ambient Storage Temperature Range -40 to 125 C Weight (typical) 3.0 oz. (86.5 gr) Encapsulation Thermally Conductive Epoxy Terminals Screws and Saddle Clamps Furnished, Unmounted Recommended Terminal Screw Torque Range: 6-32 Screws - 10 in lbs. 8-32 Screws - 20 in. lbs. (Screws dry without grase) GENERAL NOTES (1) All parameters at 25C and per section unless otherwise specied. (2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 (3) Heat sinking required, for derating curves see page 2 Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.