C8051F800-DK C8051F800 DEVELOPMENT KIT USERS GUIDE 1. Relevant Devices The C8051F800 Development Kit is intended as a development platform for the microcontrollers in the C8051F80x-83x MCU family. The members of this MCU family are as follows: C8051F800, C8051F801, C8051F802, C8051F803, C8051F804, C8051F805, C8051F806, C8051F807, C8051F808, C8051F809, C8051F810, C8051F811, C8051F812, C8051F813, C8051F814, C8051F815, C8051F816, C8051F817, C8051F818, C8051F819, C8051F820, C8051F821, C8051F822, C8051F823, C8051F824, C8051F825, C8051F826, C8051F827, C8051F828, C8051F829, C8051F830, C8051F831, C8051F832, C8051F833, C8051F834, and C8051F835. The target board included in this kit is provided with a pre-soldered C8051F800-GM MCU (QFN20 package). Code developed on the C8051F800 can be easily ported to the other members of this MCU family. Refer to the C8051F80x-83x data sheet for the differences between the members of this MCU family. The C8051F80x-GM and C8051F81x-GM devices (QFN20 package) are pin-compatible with the C8051F330/1/ 2/3/4/5/6/7 devices. 2. Kit Contents The C8051F800 Development Kit contains the following items: C8051F800 Target Board C8051Fxxx Development Kit Quick-Start Guide Silicon Labs IDE and Product Information CD-ROM. CD content includes the following: Silicon Labs Integrated Development Environment (IDE) Evaluation assembler, compiler, and linker tools Source code examples and register definition files Documentation Optional Third Party Tools CD AC to DC Power Adapter USB Debug Adapter Two USB Cables 3. Hardware Setup Refer to Figure 1 for a diagram of the hardware configuration. 1. Connect the USB Debug Adapter to the DEBUG connector on the target board with the 10-pin ribbon cable. 2. Connect one end of the USB cable to the USB connector on the USB Debug Adapter. 3. Verify that shorting blocks are installed on the target board as shown in Figure 4 on page 8. 4. Connect the other end of the USB cable to a USB Port on the PC. 5. Connect the ac/dc power adapter to power jack P4 on the target board. Notes: Use the Reset icon in the IDE to reset the target when connected during a debug session. Remove power from the target board and the USB Debug Adapter before connecting or disconnecting the ribbon cable from the target board. Connecting or disconnecting the cable when the devices have power can damage the device and/or the USB Debug Adapter. Rev. 0.2 7/13 Copyright 2013 by Silicon Laboratories C8051F800-DKC8051F800-DK PC Target Board R14 P1.4 RESET CAPACITIVE SENSE C8051F800-TB P1.0 LED J3 USB Debug D10 P1.0 LED P1.0 P1.1 LED P1.1 P1.5 COMM P1.1 LED J7J6 P1.2 LED P1.2 Adapter USB D9 P1.3 LED P1.3 D4 P1.4 SW P1.4 P1.2 LED TX MCU P0.4 D8 RX MCU P0.5 F326 RTS P1.5 P1.3 LED CTS P1.6 P1.6 USB D7 DEBUG Cable J1 GND GND P2.0 RST SILICON LABS P1.6 P1.7 www.silabs.com P1.4 P1.5 P1.2 P1.3 U1 F800 J4 P1.0 P1.1 J5 P0.6 P0.7 P0.4 P0.5 POWER P0.2 J8 P0.3 J9 XTAL1 P0.0 P0.1 P0.3 J9 P0.2 J8 +3VD +3VD J9 J8 P1 J10 GND AC/DC P0.1 Adapter VDD PWR J2 D6 +3VD TB1 GND Figure 1. Hardware Setup using a USB Debug Adapter 4. Software Setup The included CD-ROM contains the Silicon Labs Integrated Development Environment (IDE), evaluation 8051 tools, optional software utilities, and additional documentation. Insert the CD-ROM into your PCs CD-ROM drive. An installer will automatically launch, allowing you to install the IDE software or read documentation by clicking buttons on the Installation Panel. If the installer does not automatically start when you insert the CD-ROM, run autorun.exe found in the root directory of the CD-ROM. Refer to the ReleaseNotes.txt file on the CD-ROM for the latest information regarding known problems and restrictions. 4.1. System Requirements The following are the system requirements necessary to run the debug and programming tools: Pentium-class host PC running Microsoft Windows 2000 or newer. One available USB port. 4.2. Development Tools Installation To install the IDE, utilities, and code examples, perform the following steps: 1. Click on theInstall Development Tool button on the installation utility s startup screen. 2. In the Kit Selection box that appears, choose the C8051F800-DK development kit from the list of options. 3. In the next screen, choose Components to be Installed. The programs necessary to download and debug on the MCU are the Silicon Labs IDE and the Keil 8051 Evaluation Toolset. The CP210x Drivers are necessary to use the UART capabilities of the target board. See Section 4.3. for more information about installing the CP210x drivers. 4. Installers selected in Step 3 will execute in sequence, prompting the user as they install programs, documentation, and drivers. 2 Rev. 0.2 Prototype Area +3VD P0.7 P0.6/CNVSTR P1.0 P1.1 P0.1 XTAL2 GND P0.0/VREF P0.0 P0.0/VREF Silicon Laboratories USB DEBUG ADAPTER Run Stop Power