RS9113 PMOD Multi Protocol Wireless Card PRODUCT BRIEF 1x1 802.11abgn + BT4.0 + ZigBee The RS9113 PMOD Multi Protocol Wireless Card is based on Redpine Signals RS9113 ultra-low-power, single spatial stream, dual-band 802.11n + Bluetooth (BT4.0) + ZigBee (ZB) Convergence SoC. The PMOD RS9113 module is a complete IEEE 802.11 a/b/g/n, ZB and BT wireless device server that provides a wireless interface to any equipment with a UART, SPI interface. The RS9113 PMOD Multi Protocol Wireless Card integrates a multi-threaded MAC processor with integrated analog peripherals and support for digital peripherals, baseband digital signal processor, analog front-end, crystal oscillator, calibration OTP memory, dual-band RF transceiver, dual-band high-power amplifiers, baluns, diplexers, diversity switch and Quad-SPI Flash thus providing a fully-integrated solution for embedded wireless applications and all WLAN, BT and ZB protocols and networking stack functionality in embedded firmware to make a fully self-contained wireless solution for a variety of applications. The module integrates an antenna and a U.FL connector for external antenna with an option to select either one of them. The M2MCombo (RS9113) chips and modules leverage and improve upon Redpines proven low TM power innovations from Lite-Fi products (RS9110) and provide WLAN 802.11n, BT4.0 and ZB convergence solution for integration into mobile and M2M communication devices. Features and Benefits . RS9113 PMOD Multi Protocol Wireless Card module integrates WLAN, BT 4.0 and ZigBee functions WLAN: Compliant to IEEE 802.11 a/b/g/n with dual band support Bluetooth: Compliant to dual-mode Bluetooth V4.0 ZigBee: Compliant to IEEE 802.15.4. RS9113 PMOD Multi Protocol Wireless Card . Supports 20MHz bandwidth. Applications . WLAN transmit power up to +18dBm and receiver with sensitivity of -97dBm . Smart phones, Tablets and e-Readers MP3 music and MP4 video players . Support for Bluetooth Transmit power class-1 with integrated PA and high performance VoWi-Fi phones Medical Devices Bluetooth receiver with -94dBm Rx sensitivity Smart Meters and in-home displays Industrial monitoring and control Support for multiple ZigBee output powers up to +19dBm with integrated PA and high perform ance ZigBee receiver with -100dBm Rx sensitivity. Industrial automation and telemetry Home and building automation . U.FL connector for external antenna connection is selectable. Wi-Fi-BT gateway device Wi-Fi-ZB gateway device Embedded WLAN stack, ZigBee stack, BT stack, TCP/IP stack, HTTP server. Wireless headset . Support for Embedded Client mode and Access Point mode BT profile support for GAP, SPP, GATT, IAP Supports for ZigBee profiles like Home-automation and Smart Energy Supports SPI, UART host interfaces Can operate with 8-bit microcontrollers with no OS Single supply 3.0 to 3.6 V operation. RS9113 PMOD Multi Protocol Wireless Card Block Diagram R S 9 1 1 3Wireless Specifications Device Listing Device Number Description Qualification Network Standard Support IEEE 802.11 a/b/g/n, 802.11j , 802.11d/e/i, 802.11w , 802.1X, 802.11h Bluetooth v2.1 EDR, v4.0 Dual band WiSeConnect module with no antenna and Industrial 802.15.4-2009 (2.4GHz) RS9113-NBZ-D5W integrated Wi-Fi. Data Rates 802.11n: from 6.5 Mbps to 150 Mbps (MCS 0-7) 802.11a/g: from 6 Mbps to 54 Mbps Device Ordering Information 802.11b: from 1 Mbps to 11 Mbps The device numbering is based on the following naming convention. All the devices are labeled as Bluetooth: 1, 2, 3Mbps RS9113-NBZ-D5W Where. 802.15.4-2009: 250Kbps Modulation Techniques OFDM with BPSK, QPSK, 16-QAM, 64-QAM 802.11b with CCK and DSSS Bluetooth: GFSK, DQPSK, 8DPSK 802.15.4-2009: DSSS 802.11n Advanced Features 1-SS, 40MHz bandwidth, Greenfield Preamble, Short-GI, 1 spatial stream STBC, RIFS, A-MSDU, A-MPDU, Aggregation with Block-ack, A-MSDU inside A-MPDU and Virtual AP support ZigBee Advanced Features CCM* security, orphan scanning, coordinator realignment Wi-Fi modes Wi-Fi client, Access point, Wi-Fi Direct Bluetooth Modes Master, slave, scatternet ZigBee Modes ZigBee Coordinator, Router, End device QoS WMM and WMM Power Save Support Host Interfaces SPI, UART Other Peripherals/Interfaces I2C, I2S, SPI, QSPI, USART, GPIO, JTAG, Analog(ADC/DAC) and Ultra-low-power peripherals. Supply Voltage 3.0-3.6V Operating Temperature Industrial Grade -40C to +85C Software and Regulatory Certification Wi-Fi Alliance Compliance (802.11abgn, WPA, WPA2 Personal and Enterprise, WMM, WMM-PS, WPS, Wi-Fi Direct, Protected management frames ), Bluetooth-SIG (QDID-D030907) Worldwide Regulatory Compliance: FCC (IDs are XF6-RS9113SB, XF6-RS9113DB) IC (IDs are 8407A-RS9113SB, 8407A-RS9113DB) CE/ETSI, TELEC, SRRC Typical Transmit Wi-Fi: 17.5 dBm for 802.11b DSSS Power(+/-2 dBm) 17.5 dBm for 802.11g/n OFDM 12 dBm for 802.11a/g/n OFDM Bluetooth: 15 dBm ZigBee : 15 dBm Rx sensitivity Wi-Fi: 1Mbps -97 dBm (< 8% PER) (+/- 1dBm) 54 Mbps -76.5 dBm (< 10% PER) MCS7(20MHz) -73 dBm (< 10% PER) MCS7(40MHz) -69.5 dBm (< 10% PER) Bluetooth: 1 Mbps -94 dBm 2 Mbps -92 dBm 3 Mbps -84 dBm BTLE(1Mbps) -91 dBm ZigBee: 250 Kbps -102 dBm (< 8% PER) : These features are not supported by current software releases. Contact Repine Signals Sales (sales redpinesignals.com) for details. For additional information, please contact Sales at Redpine Signals, Inc.: Redpine Signals, Inc. 2107 North First Street Suite 540 San Jose, CA 95131 Phone: +1 408 748 3385 Email: sales redpinesignals.com Website: www.redpinesignals.com Redpine Signals, Inc. reserves the right to make changes to the product(s) or information contained herein without notice. No Liability is assumed as a result of their use or application.Redpine, Redpine Signals, the Redpine logo, Driving Wireless Convergence, WiSeConnect and Lite-Fi are trademarks of Redpine Signals,Inc. All other company names, products and logos are registered trademarks of their respective companies. Copyright 2017 Redpine Signals, Inc. All Rights Reserved.