DATA SHEET SKY66013-11: 700 to 800 MHz, +19 dBm Linear Power Amplifier Applications Description The SKY66013-11 linear Power Amplifier (PA) is a fully matched Residential femtocells surface mount module developed for WCDMA applications WCDMA, Bands 12, 13, 14, 17 operating from 700 to 800 MHz. The device meets the stringent Small cells spectral linearity requirements of WCDMA femtocell applications with high power-added efficiency. An integrated directional coupler eliminates the need for any external coupler. Features The GaAs MMIC contains all active amplifier circuitry, which Small signal gain: 27.5 dB includes input and interstage matching circuits. An output match into a 50 load, realized off-chip within the module package, ACLR at POUT = +19 dBm: 51 dBc optimizes efficiency and power performance. PA on/off control The SKY66013-11 is manufactured with Skyworks InGaP GaAs I/O impedance internally matched to 50 HBT process, which provides for all positive voltage DC supply Single DC supply: 3.3 V to 4.6 V operation and maintains high efficiency and good linearity. The primary bias to the device can be supplied directly from any Minimal number of external components required suitable power supply with an output of 4.2 V. Power down is Small footprint MCM (10-pin, 3 x 3 mm) package achieved by setting the VEN pin to 0 V. No external supply side (MSL3, 260 C per JEDEC J-STD-020) switch is needed since typical off leakage is a few microamps with full primary voltage supplied from the main power supply. Skyworks Green products are compliant with The SKY66013-11 is packaged in a 10-pin, 3 x 3 mm Multi-Chip all applicable legislation and are halogen-free. Module (MCM), which allows for a highly manufacturable low-cost For additional information, refer to Skyworks solution. Denition of Green, document number The 10-pin MCM package and pinout are shown in Figure 1. A SQ04-0074. functional block diagram of the SKY66013-11 is shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. 1 10 VCC1 VCC2 RF IN 2 9 RF OUT GND 3 8 CPL IN GND 4 7 GND 5 6 VEN CPL OUT S2992 Figure 1. SKY66013-11 Pinout 10-Pin MCM (Top View) Skyworks Solutions, Inc. Phone 781 376-3000 Fax 781 376-3100 sales skyworksinc.com www.skyworksinc.com 202854C Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice March 6, 2014 1 DATA SHEET SKY66013-11: LINEAR POWER AMPLIFIER MMIC VEN VCC1 Driver Stage Power Stage Bias Bias Output Input Inter-Stage RF IN DA PA RF OUT Match Match Match VCC2 CPL OUT CPL IN S2993 Figure 2. SKY66013-11 Linear PA Block Diagram Table 1. SKY66013-11 Signal Descriptions Pin Name Description Pin Name Description 1 VCC1 Input stage supply voltage 6 CPL OUT RF coupler output 2 RF IN RF input port 7 GND Ground 3 GND Ground 8 CPL IN RF coupler input 4 GND Ground 9 RF OUT RF output port 5 VEN Enable 10 VCC2 Output stage supply voltage Technical Description Electrical and Mechanical Specifications The SKY66013-11 PA contains all of the needed RF matching and The absolute maximum ratings of the SKY66013-11 are provided DC biasing circuits. The device is a two-stage, HBT InGaP device in Table 2. The recommended operating conditions are specified optimized for high linearity and power efficiency. These features in Table 3 and electrical specifications are provided in Table 4. make the device suitable for wideband digital applications where PA linearity and power consumption are of critical importance (e.g., small cell and infrastructure applications). The device is designed for standard WCDMA modulated signals. Under these stringent test conditions, the device exhibits excellent spectral purity and power efficiency. Skyworks Solutions, Inc. Phone 781 376-3000 Fax 781 376-3100 sales skyworksinc.com www.skyworksinc.com 2 March 6, 2014 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice 202854C