GPMP SERIES SINGLE OUTPUT MEDICAL POWER SUPPLY
High Power Supplies 600/700 Watt AC/DC Universal Input Power Supply
SUMMARY
90 -264 Vac nominal input range g
Overvoltage and short circuit protection
Approved to UL, CSA and EN Standards
Power Good LED
Low Leakage
The GPMP Series are universal input AC/DC medically ap-
proved power supplies with power factor correction (PFC) and
up to 700 Watts ouput power. The GPMP product in corporates
hot-swap capabilities and a handle. The series is approved to
EN60601-1 to reduce design-in time and end system compli-
ance costs
O
All specifications are typical at nominal input, full load at 25 C unless otherwise stated
SPECIFICATIONS
OUPUT SPECIFICATIONS INPUT SPECIFICATIONS
Output Power Integral forced air 700 Watts max. Input Voltage range Universal input 100-240 nom (85 - 264 max)
Vac
Total Regulation See table
Input frequency 47 Hz to 63 Hz
Rise time At turn-on 2.0 s max.
Input surge current 25 A max.
Transient response Main output 25% 3.5% max. dev. 350 ms recovery
0.1 A/ ms to 1% Ground Leakage current 264 Vac 60 Hz 160 mA
Temperature Coef- +/-0.03%/oC Input current 120 Vac 8.5 A
ficient
230 Vac 4.5 A
Overvoltage protection 125% +/-10%
Input fuse F1,F2 10.0 A
Short Circuit protection block wall Yes
EMC INFORMATION ENVIRONMENTAL SPECIFICATIONS
o o
Conducted emissions EN55011 Level B Thermal Performance operating ambient -20 C -50 C
(see ratings chart)
Radiated emissions EN55011 Level A
o
non-operating -40 to +85 C
Line freq. harmonics EN61000-3-2 Class A
o
0 - 50 C 600 Watts
Voltage fluctuations EN61000-3-3 Complies (clause 5b)
Convection cooled
ESD Air EN61000-4-2 8 kV contact
Maximum Altitude operating / non-operating 10,000 ft. / 40,000
ESD Contact EN61000-4-2 6 kV air
ft. max.
Relative Humidity non-condensing 5% - 95% RH
Radiated immunity EN61000-4-3 3 V/m
2
Vibration (operating) 0.003 g /Hz 1.5 g 3 axes 10
Fast Transients (EFT) EN61000-4-4 2 kV 5 kHz
rms
min/axis
Line surge immunity EN61000-4-5 1 kV diff /2 kV cm
2
Vibration (non-operating) 0.026 g /Hz 5.0 g 3 axes, 1
rms
Conducted immunity EN61000-4-6 3 Vrms
hr/axis
Power freq. mag. field EN61000-4-8 3 A/m
Shock half-sine 20 g 10 ms, 3 axes, 6
pk
shocks total
Voltage dip immunity EN61000-4-11 Unit will ride through without loss of
output at 75% of rated load with AC
Shock half-sine 40 g 10 ms, 3 axes, 6
pk
power fail warning.
shocks total
Page 1 of 3GENERAL SPECIFICATIONS
Hold-up time 120 Vac, 60 Hz 30 ms at 600 Watts output
Efficiency 120 Vac 600 W output >84 %
isolation voltage input to ouput 4000 Vac
input to ground 1500 Vac
Switching frequency fixed 70 KHz, +/- 10 KHz
Safety Approvals UL/EN/IEC 60601-1 CSA22.2 No.60601-1
Maximum weight 2 kg (4.4 lbs)
MODEL NUMBER Output Peak Output Ripple Regulation
GPMP600-24 24 V 25 A 24 V 27 A 240 mV 1%
GPMP600-28 28 V 21.5 A 28 V 23.5 A 240 mV 1%
GPMP600-36 36 V 17 A 36 V 19 A 240 mV 1%
GPMP700-48 48 V 14 A 48 V 15.6 A 240 mV 1%
NOTES
1. Integral forced air cooling
2. Peak rating is for 1 minute maximum 10% duty cycle
3. Noise measurent 20 MHz Bandwidth, differential mode. Measured with scope probe directly across output terminals of the power supply.
MECHANICAL NOTES
The GPMP series is factory configured for stand alone installation with multiple configurations of output connectors. Apart from the DIN 41612 option
there are three Phoenix contact connector options shown in the drawing on page 3.
The GPHP (commercial series) can be configured with Condor CRA series racks. Other mounting configurations and connector options are available,
Please contact factory.
POWER CONNECTOR DIN # 41612 Type H
INPUT PINS
Z-32 AC Line
D-30 AC Neutral
Z-28, D26 GROUND
OUTPUT PINS
Z12, D14, Z16,D18 OUTPUT
Z4, D6, Z8, D10 RETURN (COMMON)
STATUS & CONTROL PINS
Z20 DC POWER GOOD
Z24 INHIBIT
D22 AC POWER FAIL
Page 2 of 3