PCA9306 2 Dual bidirectional I C-bus and SMBus voltage-level translator Rev. 9.1 31 August 2021 Product data sheet 1 General description 2 The PCA9306 is a dual bidirectional I C-bus and SMBus voltage-level translator with an enable (EN) input, and is operational from 1.0 V to 3.6 V (V ) and 1.8 V to 5.5 V ref(1) (V ). bias(ref)(2) The PCA9306 allows bidirectional voltage translations between 1.0 V and 5 V without the use of a direction pin. The low ON-state resistance (R ) of the switch allows connections on to be made with minimal propagation delay. When EN is HIGH, the translator switch is on, and the SCL1 and SDA1 I/O are connected to the SCL2 and SDA2 I/O, respectively, allowing bidirectional data flow between ports. When EN is LOW, the translator switch is off, and a high-impedance state exists between ports. The PCA9306 is not a bus buffer like the PCA9509 or PCA9517A that provide both level translation and physically isolate the capacitance to either side of the bus when both sides are connected. The PCA9306 only isolates both sides when the device is disabled and provides voltage level translation when active. The PCA9306 can also be used to run two buses, one at 400 kHz operating frequency and the other at 100 kHz operating frequency. If the two buses are operating at different frequencies, the 100 kHz bus must be isolated when the 400 kHz operation of the other bus is required. If the controller is running at 400 kHz, the maximum system operating frequency may be less than 400 kHz because of the delays added by the translator. 2 As with the standard I C-bus system, pull-up resistors are required to provide the logic HIGH levels on the translators bus. The PCA9306 has a standard open-collector 2 configuration of the I C-bus. The size of these pull-up resistors depends on the system, but each side of the translator must have a pull-up resistor. The device is designed to 2 work with Standard-mode, Fast-mode and Fast-mode Plus I C-bus devices in addition to SMBus devices. The maximum frequency is dependent on the RC time constant, but generally supports > 2 MHz. When the SDA1 or SDA2 port is LOW, the clamp is in the ON-state and a low resistance connection exists between the SDA1 and SDA2 ports. Assuming the higher voltage is on the SDA2 port when the SDA2 port is HIGH, the voltage on the SDA1 port is limited to the voltage set by VREF1. When the SDA1 port is HIGH, the SDA2 port is pulled to the drain pull-up supply voltage (V ) by the pull-up resistors. This functionality allows a pu(D) seamless translation between higher and lower voltages selected by the user without the need for directional control. The SCL1/SCL2 channel also functions as the SDA1/SDA2 channel. All channels have the same electrical characteristics and there is minimal deviation from one output to another in voltage or propagation delay. This is a benefit over discrete transistor voltage translation solutions, since the fabrication of the switch is symmetrical. The translator provides excellent ESD protection to lower voltage devices, and at the same time protects less ESD-resistant devices.NXP Semiconductors PCA9306 2 Dual bidirectional I C-bus and SMBus voltage-level translator 2 Features and benefits 2 2-bit bidirectional translator for SDA and SCL lines in mixed-mode I C-bus applications 2 Standard-mode, Fast-mode, and Fast-mode Plus I C-bus and SMBus compatible Less than 1.5 ns maximum propagation delay to accommodate Standard-mode and 2 Fast-mode I C-bus devices and multiple controllers Allows voltage level translation between: 1.0 V V and 1.8 V, 2.5 V, 3.3 V or 5 V V ref(1) bias(ref)(2) 1.2 V V and 1.8 V, 2.5 V, 3.3 V or 5 V V ref(1) bias(ref)(2) 1.8 V V and 3.3 V or 5 V V ref(1) bias(ref)(2) 2.5 V V and 5 V V ref(1) bias(ref)(2) 3.3 V V and 5 V V ref(1) bias(ref)(2) Provides bidirectional voltage translation with no direction pin Low 3.5 ON-state connection between input and output ports provides less signal distortion 2 Open-drain I C-bus I/O ports (SCL1, SDA1, SCL2 and SDA2) 2 5 V tolerant I C-bus I/O ports to support mixed-mode signal operation High-impedance SCL1, SDA1, SCL2 and SDA2 pins for EN = LOW Lock-up free operation Flow through pinout for ease of printed-circuit board trace routing ESD protection exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101 Packages offered: SO8, TSSOP8, VSSOP8, XQFN8, XSON8 3 Ordering information Table 1.Ordering information Type number Topside Package mark Name Description Version PCA9306D PCA9306 SO8 SOT96-1 plastic small outline package 8 leads body width 3.9 mm 1 PCA9306DC1 P06 VSSOP8 SOT765-1 plastic very thin shrink small outline package 8 leads body width 2.3 mm PCA9306DC1/ P06 VSSOP8 SOT765-1 plastic very thin shrink small outline package 8 leads 2 DG body width 2.3 mm 3 PCA9306DP 306P TSSOP8 SOT505-1 plastic thin shrink small outline package 8 leads body width 3 mm 4 PCA9306DP1 306T TSSOP8 SOT505-2 plastic thin shrink small outline package 8 leads body width 3 mm lead length 0.5 mm 5 PCA9306GF 06 XSON8 extremely thin small outline package no leads 8 SOT1089 terminals body 1.35 x 1 x 0.5 mm 6 PCA9306GM P6X XQFN8 SOT902-2 plastic extremely thin quad flat package no leads 8 terminals body 1.6 x 1.6 x 0.5 mm 1 Same footprint and pinout as the Texas Instruments PA9306DCU. VSSOP8 transfers to ASEN in dark green - refer to PCN202103046A. PCA9306 All information provided in this document is subject to legal disclaimers. NXP B.V. 2021. All rights reserved. Product data sheet Rev. 9.1 31 August 2021 2 / 32