TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TO-220 ITO-220 Pin Definition: 1. Input 2. Ground (tab) 3. Output General Description The TS7800 series voltage regulators are monolithic integrated circuits designed as fixed-voltage regulators for a wide variety of applications including local, on-card regulation. These regulators employ internal current limiting, thermal shutdown, and safe-area compensation. With adequate heatsink they can deliver output currents up to 1 ampere. Although designed primarily as a fixed voltage regulator, these devices can be used with external components to obtain adjustable voltages and currents. Features Standard Application Circuit Output Voltage Range 5 to 24V Output current up to 1A No external components required Internal thermal overload protection Internal short-circuit current limiting Output transistor safe-area compensation Output voltage offered in 4% tolerance A common ground is required between the input and the Ordering Information output voltages. The input voltage must remain typically 2.0V above the output voltage even during the low point on Part No. Package Packing the Input ripple voltage. TS78xxCZ C0 TO-220 50pcs / Tube XX = these two digits of the type number indicate voltage. * = Cin is required if regulator is located an appreciable TS78xxCI C0 ITO-220 50pcs / Tube distance from power supply filter. Note: Refer to detail ordering information table. ** = Co is not needed for stability however, it does improve transient response. o Absolute Maximum Ratings (T = 25 C unless otherwise noted) A Parameter Symbol Limit Unit V =5~18V 35 OUT Input Voltage V V IN V =24V 40 OUT Output Current I Internal Limited OUT Power Dissipation P Internal Limited D o Operating Junction Temperature T 0~+125 C J o Storage Temperature Range T -65~+150 C STG TO-220 5 o Thermal Resistance - Junction to Case R C/W JC ITO-220 5 TO-220 50 o Thermal Resistance - Junction to Ambient R C/W JA ITO-220 60 Note: Absolute maximum ratings are those values beyond which damage to the device may occur. Functional operation under these conditions are not implied. 1/9 Version: E14 TS7800 Series 3-Terminal Fixed Positive Voltage Regulator TS7805 Electrical Characteristics o o (V =10V, I =500mA, 0 CT 125 C, C =0.33F, C =0.1F unless otherwise specified.) IN OUT J IN OUT Parameter Symbol Test Condition Min Typ Max Unit o T =25 C 4.80 5 5.20 J Output voltage V V 7.5VV 20V, OUT IN 4.75 5 5.25 10mAI 1A, P 15W OUT D 7.5VV 25V -- 3 100 IN o Line Regulation REG T =25 C LINE J 8VV 12V -- 1 50 IN mV 10mAI 1A -- 15 100 OUT o Load Regulation REG T =25 C LOAD J 250mAI 750mA -- 5 50 OUT o Quiescent Current I I =0, T =25 C -- 4.2 8 Q OUT J 7.5VV 25V -- -- 1.3 mA IN Quiescent Current Change I Q 10mAI 1A -- -- 0.5 OUT o Output Noise Voltage V 10Hzf100KHz, T =25 C -- 40 -- V N J Ripple Rejection Ratio RR f=120Hz, 8VV 18V 62 78 -- dB IN o Voltage Drop V I =1.0A, T =25 C -- 2 -- V DROP OUT J Output Resistance R f=1KHz -- 17 -- m OUT o Output Short Circuit Current I T =25 C -- 750 -- mA OS J o Peak Output Current I peak T =25 C -- 2.2 -- A O J Temperature Coefficient of o o o V / T I =10mA, 0 CT 125 C -- -0.6 -- mV/ C OUT J OUT J Output Voltage TS7808 Electrical Characteristics o o (V =14V, I =500mA, 0 CT 125 C, C =0.33F, C =0.1F unless otherwise specified.) IN OUT J IN OUT Parameter Symbol Test Condition Min Typ Max Unit o T =25 C 7.69 8 8.32 J Output Voltage V 10.5VV 23V, 10mAI 1A, V OUT IN OUT 7.61 8 8.40 P 15W D 10.5VV 25V -- 6 160 IN o Line Regulation REG T =25 C LINE J 11VV 17V -- 2 80 IN mV 10mAI 1A -- 12 160 OUT o Load Regulation REG T =25 C LOAD J 250mAI 750mA -- 4 80 OUT o Quiescent Current I I =0, T =25 C -- 4.3 8 Q OUT J 10.5VV 25V -- -- 1 mA IN Quiescent Current Change I Q 10mAI 1A -- -- 0.5 OUT o Output Noise Voltage V 10Hzf100KHz, T =25 C -- 52 -- V N J Ripple Rejection Ratio RR f=120Hz, 11VV 21V 56 72 -- dB IN o Voltage Drop V I =1.0A, T =25 C -- 2 -- V DROP OUT J Output Resistance R f=1KHz -- 16 -- m OUT o Output Short Circuit Current I T =25 C -- 450 -- mA OS J o Peak Output Current I peak T =25 C -- 2.2 -- A O J Temperature Coefficient of o o o V / T I =10mA, 0 CT 125 C -- -0.8 -- mV/ C OUT J OUT J Output Voltage Pulse testing techniques are used to maintain the junction temperature as close to the ambient temperature as possible, and thermal effects must be taken into account separately. This specification applies only for DC power dissipation permitted by absolute maximum ratings. 2/9 Version: E14