Switch Mode Power Supply Model Highly Accelerated PAS150 H . A . L . T. Life TESTED Testing 150 Watts output power max Power Factor Correction Single Output Electrical Specifications Input Voltage: 85-132/180-264 VAC, 47-63 Hz, 1 phase Input Current: <3.2A RMS 115 VAC full load <1.6A RMS 230 VAC full load Inrush Current: <25A, pk 132 VAC cold start <50A, pk 265 VAC cold start Harmonic Distortion: Meets EN61000-3-2 for Class A EMI Filtering: Meets CISPR 11 and 22 and FCC Part 15 Class B (conducted) Input Protection: Internal AC line fuse 250 VAC, 6.3A Thermal Shutdown Standard Output Power: 150W with 15CFM air 80W Convection DC OK: Standard Open Collector Line Regulation: 0.3% Turn-on Delay: <1 second after application of AC Input Load Regulation: 0.5% P Stability: <0.1% for 8 hours ARD: <1% or 50mV after 1/2-hour warm up 20MHz bandwidth Isolation: >20 M 100 VDC between output Hold-up Time: 20 ms full load (120 VAC) terminals and chassis ground Output Polarity: Output is floating AC Power Fail: TTL logic 0 at least 2 ms before LOW Minimum Load: 0% of rated load output drops 5% Open Collector Transient Response: 3% for 25% load change 1A/s Overvoltage Protect: Factory set, 125% 5%, 50% duty cycle 50/60 Hz cycle AC to reset Output Rise Time: <100 ms (10% to 90%) Reverse Voltage: Output has reverse voltage protection Current Limit: 105-130% of rated current Hiccup Reverse current limited to 100% of output rating Remote Sense: Compensates for up to 250mV of total cable drop Efficiency: Up to 85% Remote On/Off: Optional MTBF: MIL-STD-HDBK 217E >200,000 hours 25C Highly Accelerated Life Testing Available Voltage Outputs* Continuous Voltage Voltages Current Codes (Volts) (Amps) -2 3.3 30 -3 5.0 30 -4 12.0 12.5 -5 15.0 10.5 -6 24.0 6.5 -7 28.0 5.5 -8 36.0 4.5 -9 48.0 3.5 * Consult factory for other voltages and OEM quantities. Note: Standard models are shown bold PART STRUCTURE: MODEL - VOLTAGE CODE - OPTION CODES (See back) - V1 - PAS150 - X - ABC.... Example: Part Number PAS150-4-CF= 150W Power Factor Corrected, 12V 12.5A with a fan assembly and power fail invert. See 3rd page for PAS150 CODE TABLE AND AVAILABLE OPTIONS. Model PAS150 Surge & ESD Test Levels Options EN61000-4-5 Level 3 EN61000-4-2 Level 2 EN61000-3-2 for Class A EN61000-4-2 Level 3 (Air Only) 12V 0.5A Aux./Fan Drive (A) Droop Current Share 10% (B) EN61000-4-4 Level 3 EN61000-4-11 Fan Assembly (C) DC OK Invert (E) PF Invert (F) Field-Configurable (G) Meets Class B conducted limits per CISPR 11/22 and 47 CFR 15 subpt B Single Wire Current Share 5% (I) Square Current Limit (J) Molex Connector (K) Metric Mounting (M) Physical Specifications OR-ing Diode (O) Remote On/Off (R) Dimensions: (HxWxL) 1.5 x 4.0 x 6 Remote On/Off Invert (S) Operating Temp: 0 to 70C rated power to 50C Safety Compliance derate linearly to 50% at 70C. IEC / EN / UL / CSA 60950-1 CE Declaration to Low Voltage Directive 2006/95/EC and Relative Humidity: 5% to 90%, non-condensing RoHS Directive 2011/65/EU Storage: -50 to 85C/20-90% RH Altitude: 6561 40,000 storage Copyright 2011 TAMURA CORPORATION OF AMERICA. Specifications subject to change without notice. TAMURA CORPORATION OF AMERICA 1040 South Andreasen Drive, STE. 100 Escondido, CA 92029-1951 (951) 699-1270 / Fax: (951) 676-9482 (800) 472-6624 www.tamuracorp.com