CPFE500F Series 500W Conduction Cooled Power Supplies Features Base plate cooled, no fan required High e ciency Protective coating option MIL STD 461/462D CE102 Conducted EMC Key Market Segments & Applications Speci cations Model AC Input VAC/Hz 90 to 265VAC, 47-63Hz (up to 440Hz) (3) Input Current Model dependant (1) A 6.8 / 3.4 Inrush Current (115 / 230VAC) A 20 / 40 peak Power Factor - Meets EN61000-3-2 E ciency (typical) % 85% at 75% loading (Non ORing diode versions) Output Voltage Setpoint Accuracy - 2% at 50% load Total Regulation % < 4%. (ORing diode option, adds 1V to load regulation) Ripple and Noise (20MHz BW) - 1% (1.5% below -10C) Over Current Protection % 105 - 140% (Automatic Recovery) Over Voltage Protection - 125 - 145% (Cycle AC to reset) Series Operation - Yes Parallel Operation - Yes (Single wire, up to 6 units) ORing Diodes/FETs - Yes (option) Power On Signal (ENA) - Open collector (10mA sink current). Low (on) when output is present Auxiliary Supply - 10 - 14V, 20mA Remote On/O (Opto isolated) - High = On Temperature Coe cient - <0.01%/C Overtemperature C Shuts down between 90 - 130C (Cycle AC to reset) Hold Up Time (230VAC) ms 10ms Leakage Curr. (at 230VAC, 50Hz) mA < 1.5mA Remote Sense - Yes, compensates up to 500mV cable drop Operating Temp. (Base plate) C -40 to +85C (2) Storage Temperature C -40 to +100C Humidity - Operating: 20 - 95%RH, Non operating 10 - 95%RH (Pcb assembly protective coated) Cooling - Conduction cooled through 6mm base plate Withstand Voltage - Input to Output 4242VDC, Input to Ground 2121VDC, Output to ground 500VDC Vibration (non operating) - MIL-STD-810E, Method 514.4, Proc 1, Category 1, 9 Shock - MIL-STD-810E, Method 516.5, Proc. I, IV, VI Safety Agency Approvals - UL60950-1, CSA 22.2 No 60950-1, EN60950-1 (Ed 2), CE Mark Line Dip - Complies with SEMI F47 (200VAC line only) Conducted EMI - EN55011, EN55022 (as per CISPR, 11/22) Class B, FCC47 part 15 subpart B) MIL STD 461E/461E/462D CE102, 115V and 220V Radiated EMI - EN55011, EN55022 (as per CISPR, 11/22) Class B, FCC47 part 15 subpart B) see app. note for details Immunity - IEC61000-4-2 (Contact Level 2, Air discharge Lvl 3), -3 (Lvl 3), -4(Lvl 3), -5 (Lvl 4), -6 (Lvl 3), -8 (Lvl 4), -11 (Class 3 ), -12 (Lvl 3), -14 (Class 3) Weight (Typ) g with cover 1400g, without cover 1200g Size (L x W x D) mm 270 x 126 x 55mm Warranty yrs 2 years (1) 100/200VAC (2) CPFE500F-12: -40 to 80C. See instruction manuals for derating curves (3) Reduced PFC above 63Hz. Contact technical support for 440Hz operation. Last time buy July 2019 1-800-526-2324 www.us.tdk-lambda.com/lp/ 32 Disclaimer: us.tdk-lambda.com/lp/legal.htmCPFE500F Series Model Selector Options Output Adjust Max Max ORing Protective Model Volt (V) Range (V) Curr (A) Watt (W) Part Number Desc. Su x Diode (3) Cover Coating CPFE500F-12-NLC 12 9.6 - 14.4 42 504 -DLC Y Y Y CPFE500F-24-NLC 24 22.4 - 33.6 18 504 -NLC N Y Y CPFE500F-28-NLC 28 22.4 - 33.6 18 504 3) Reduces maximum output adjustment range by 1V CPFE500F-48-NLC 48 38.4 - 57.6 10.5 504 Preferred stocking part highlighted in blue. Outline Drawing For Additional Information, please visit us.tdk-lambda.com/lp/products/cpfe-series.htm Last time buy July 2019 1-800-526-2324 www.us.tdk-lambda.com/lp/ 33 Revision A9: Aug 2018