ASSY USED ON: CODE 54 - HEAT SHRINK BOOT BACKSHELL 201M116-19C-D SERIES DASH NUMBER (TABLE 1) MATERIAL REFER TO CH00-0250-004 FINISH REFER TO CH00-0250-004 MODIFICATION CODE REFER TO CH00-0250-004 2 NOTES: 1. THIS PRODUCT IS DESIGNED TO TERMINATE A HEAT SHRINKABLE LIPPED BOOT TO A CONNECTOR. 2. FOR ADDITIONAL DIMENSIONS, ORDERING INFORMATION AND MODIFICATIONS, SEE CH00-0250-004. 3. ADAPTOR TO BE PERMANENTLY MARKED/BAGGED AND LABELLED WITH CODE IDENTIFICATION NUMBER AND PART NUMBER. (e.g. 06090-201M112-19A). 4. BACKSHELL MATES TO MIL-C-81703, SERIES III, MS3424, MS3446, MS3464, MS3467, MS3468, CLASS E & L 5. BACKSHELL MATES TO MIL-C-5015G, MS3400 SERIES, CLASS D, E, K, L, U & W, MS3400, MS3401, MS3404, MS3406,MS3450, MS3451, MS3454, MS3456, MS3470, MS3471, MS3472, MS3474, MS3475, MS3476. MIL-C-83723, SERIES II, CLASS A & L. MIL-C-83723, SERIES I & III, CLASS A, G, K, R & S: M83723/1, /2, /3, /4, /5, /6, /7, /8, /13, /14, /36, /37, /38, /40, /41, /42, /43, /48, /49, /65, /66, /67, /68, /69, /70, /71, /72, /73, /74, /75, /76, /77, /78, /82, /83, /84, /85, /86, /87, /91, /92, /95, /97, /98, (MS3155 CONTROLLED INTERFACE). 6. WHEN MODIFICATION IS SPECIFIED, COUPLING NUT SHALL HAVE 3 WIRE HOLES, 120 APART. DATE 3RD ANGLE DRAWN K.WINCZURA TITLE: PROJECTION 19/02/2015 NOT TO CHECKED 19/02/2015 SCALE HEAT SHRINK BOOT BACKSHELL UNLESS OTHERWISE SPECIFIED APPROVED K.SHEPPARD 03/03/2015 ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM APPROVED H.SMITH 20/08/2015 ANGULAR +/- 1 REVISIONS LTR DATE APPROVED DESCRIPTION MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III J2 26/03/2015 H.SMITH REVISED PER ECO-15-004707 K REVISED PER ECO-15-011999 20/08/2015 H.SMITH TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING DRAWING NO: DRAWING REV: SHT TE CAGE CODE: 06090 AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. 201M1XX K 1 POLAMCO/TE CAGE CODE: U5792ASSY USED ON: A-A E REF. 26,90 MAX A G 3,50 STAINLESS STEEL TEETH VIEW PART MARK MEDIUM DIAMOND HERE KNURL 6 A TABLE 1 BASE PART SHELL A B Z Y X E G +0,00/-0,50 +0,20/-0,00 NUMBER SIZE THREAD MAX MIN REF. 201M103 03 9/16 -24UNEF 17,0 6,6 13,5 1,12 10,5 28,0 15,6 6,6 13,5 1,12 10,5 28,0 201M108 08 1/2 -20UNF 201M110 10 5/8 -24UNEF 18,6 9,3 15,4 1,12 10,5 28,0 21,7 12,8 19,7 1,12 10,5 28,0 201M112 12 3/4 -20UNEF 201M114 14 7/8 -20UNEF 24,9 14,7 21,3 1,12 10,5 28,0 28,2 17,8 24,5 1,12 10,5 28,0 201M116 16 1 -20UNEF 201M118 18 30,9 19,8 26,5 1,12 10,5 28,0 1 1/16 -18UNEF 201M120 20 1 3/16 -18UNEF 34,1 23,0 30,9 1,75 10,5 28,0 37,3 26,2 34,4 1,75 10,5 28,0 201M122 22 1 5/16 -18UNEF 201M124 24 1 7/16 -18UNEF 40,4 29,1 36,8 1,75 10,5 28,0 50,0 35,1 43,4 1,75 10,5 28,0 201M128 28 1 3/4 -18UNS 201M132 32 2 -18UNS 56,3 41,3 48,7 2,20 14,5 32,3 62,7 46,8 55,1 2,20 14,5 32,3 201M136 36 2 1/4 -16UN 69,0 52,2 61,0 2,20 14,5 32,3 201M140 40 2 1/2 -16UN 201M144 44 2 3/4 -16UN 75,4 58,7 67,5 2,20 14,5 32,3 81,7 65,1 73,8 2,20 14,5 32,3 201M148 48 3 -16UN 201M161 61 1 1/2 -18UNEF 42,0 30,1 38,8 1,75 10,5 28,0 DATE 3RD ANGLE DRAWN K.WINCZURA TITLE: PROJECTION 19/02/2015 NOT TO CHECKED 19/02/2015 SCALE HEAT SHRINK BOOT BACKSHELL UNLESS OTHERWISE SPECIFIED APPROVED K.SHEPPARD 03/03/2015 ALL DIMENSIONS IN MILLIMETRES GENERAL TOL LINEAR +/-0,25MM APPROVED H.SMITH 20/08/2015 ANGULAR +/- 1 REVISIONS LTR DATE APPROVED DESCRIPTION MIL-DTL-26482 SERIES II / MIL-DTL-83723 SERIES I & III J2 26/03/2015 H.SMITH REVISED PER ECO-15-004707 K REVISED PER ECO-15-011999 20/08/2015 H.SMITH TE CONNECTIVITY - POLAM CO LTD RESERVES THE RIGHT TO AMEND THIS DRAW ING DRAWING NO: DRAWING REV: SHT TE CAGE CODE: 06090 AND THE INFORMATION SET FORTH HEREON AT ANY TIM E. USERS SHOULD INDEPENDENTLY EVALUATE THE SUITABILITY OF THE PRODUCT FOR THEIR APPLICATION. 201M1XX K 2 POLAMCO/TE CAGE CODE: U5792 B A THREAD XXXX Z X Y