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efer to Application Specification 11413183 or Application and Termination Requirements for these contacts. Figure 1 adjustable ratchet that ensures full contact crimping. PROCRIMPER III Hand Tool Assembly 20632911 The tool frame holds a die assembly with three consists of Die Assembly 20632912 and crimping sections. PROCRIMPER III Hand Tool Frame 3549401. The die assembly consists of crimping dies and a locator The die assembly features a wire anvil, an insulation assembly. Read these instructions thoroughly before anvil, a wire crimper, and an insulation crimper. crimping any contacts. Attached to the outside of the frame is a locator assembly, which contains a locator, a spring retainer, and a contact support. Die retaining pins and die retaining screws are used /- 8+9 4* to position and secure the dies in the tool frame. A The tool features a tool frame with a stationary jaw nut is used on the upper die retaining screw to hold and handle, a moving jaw, a moving handle, and an the locator assembly in place/9)54:8522+**5) 3+4:/99 (0+)::5).4-+ )5 2+):854/)9 58658:/54 88/9( 8- 5, 22 4:+84:/542 /-.:9 +9+8<+* % 582:+9:8+</9/544+-/542 9:53+8 +8</)+ 25-54* )5 2+):854/)98+:8*+3819 </9/:5 8=+(9/:+:111 02%-*%0.-,)%/ %-+ 8*+381 :.+8685* ):9 25-59 4*)5364 43+9 9+*8+:.+6856+8: 5,:.+/88+96+):/<+5=4+89 ((% )) %* % ( % & % & Figure 2 9. Place the locator assembly over the end of the long screw, and position the locator assembly against the side of the tool jaw. 1. Open the tool handles and remove the two die 10. Place the nut onto the end of the long screw retaining screws from the tool jaws. and tighten the nut enough to hold the locator assembly in place, while still allowing the locator to 2. Place the wire anvil and insulation anvil so that slide up and down. their chamfered sides and their marked surfaces face outward, when mounted in the moving jaw of 11. To disassemble, close the tool handles until the the tool frame. ratchet releases, remove the nut, the locator assembly, the two die retaining screws, and the 3. Insert the two die retaining pins. four die retaining pins, and slide the anvils and crimpers out of the tool jaws. 4. Insert the short die retaining screw through the jaw and through both anvil dies, and tighten the screw just enough to hold the dies in place. Do not tighten the screw completely at this time. 5. Place the wire crimper and insulation crimper so that their chamfered sides and their marked surfaces face outward, when mounted in the 1. Make a sample crimp and determine if the stationary jaw of the tool frame. contact is straight, bending upward, or bending downward. 6. Insert the two die retaining pins. 2. If adjustment is required, loosen the screw that holds the contact support onto the locator 7. Insert the long die retaining screw through the assembly. jaw and through both crimper dies, and tighten the screw just enough to hold the dies in place. Do not tighten the screw completely at this time. 8. Carefully close the tool handles, making sure that the anvils and crimpers align properly. Continue closing the tool handles until the ratchet 3. Place a contact with wire into the proper nest in the tool frame has engaged sufficiently to hold and close the tool handles until the ratchet reaches the anvils and crimpers in place, then tighten both the sixth click, or until the contact support touches die retaining screws. the contact. ( &