267587-32 ,))7 % && % +&(* % &( , () &- ( & + &%% *&() )9 )%7-2+ 330 322)735 )* 5-27)( -58-7 3%5( )* 327%7 844357 29-0 3%5( 844357 - 785) )* Figure 1 The seating tool and support anvil are each Seating Tool 2244411 and Support Anvil 2244421 onepiece aluminum. The support anvil is positioned are used to seat UPM Connectors 2239611 and into a pc board support fixture to support the pc 2239621. See Figure 1. The connectors contain board. During seating, the seating tool covers the ACTION PIN contacts to allow solderless pc board connector and presses on the top surface of the installation. connector when the applicator ram applies force to the seating tool. & ( +&(* .*+( A pc board support must be used to provide proper Read these instructions and understand them before support for the pc board and alignment of the tool to using the seating tool and support anvil. the contacts and to protect the pc board and contacts Reasons for reissue of this instruction sheet are from damage. PC Board Support Fixture 679980 provided in Section 7, REVISION SUMMARY. is recommended for use with this seating tool and ,-63275300)((381)27-668&.)773,%2+) <3 0)7532-6 35435%7-32 %55-6&85+ 3* 00 27)52%7-32%0 -+,76 )6)59)( 350%7)675)9-6-32%2( )+-32%0 86731)5 )59-) 03+3%2( <3 0)7532-6%5)75%()1%5/6 9-6-7385:)&6-7)%7 --- */ & *(& ) & 5%()1%5/ 7,)5453(876 03+36 %2(314%2<2%1)686)(%5)7,)4534)57<3*7,)-55)64)7-9)3:2)56 & support anvil. For proper selection and usage 5. Position the seating tool onto the connector. information, refer to instruction sheet 4084038. 6. Center seating tool and connector under the applicator ram of the power source slowly lower ram until it just meets the seating tool. Verify the alignment of the board support, pc board, connector, seating tool, and support anvil. % % % Power for seating must be provided by a machine capable of supplying a downward force of 89 Newtons % (N) 20 lb per contact. Contact TOOLING % ASSISTANCE CENTER at the number at the bottom of page 1 for recommendations. 7. Cycle applicator ram according to instructions for the power source. Check assembly for proper seating using the requirements in Figure 2. 1. Set seating height to the dimension shown in 8. Remove pc board with seated connector, or Figure 2 (applicator shut height will equal the reposition board and board support for seating seating height PLUS the combined thicknesses of additional connectors. the pc board, support anvil, and pc board support). 2. Position the support anvil, grooved side up, into the pc board support fixture and center it under the The seating tool and support anvil are inspected applicator ram of the application tooling. Position before shipment. It is recommended that the tool and the pc board over the support anvil. support anvil be inspected immediately upon its 3. Position the connector into pc board so that arrival at your facility to ensure that it has not been contacts are properly aligned to the pc board and damaged during shipment. Refer to Figure 3 for support anvil. See Figure 2. dimensions. 4. Insert connector into pc board until ACTION PIN Regular inspections should be performed by quality sections of the contacts are resting securely on, control personnel. A record of scheduled inspections but have not fully entered, the pc board. should remain with the seating tool and support anvil -1 1- *% ..*)1-/ + 2**6 -4, %& 1), %)(1 1), --* %,1%/% -,,% 1-/ 1% , %/ ..*)1-/ +, ++ -11-+% -, -,,% 1-/ ), / %& ..*)1-/ (21 %)(1 + 2**6 -4, -,1 10 *),% 4)1( -*%0 %% % 1)-, 1%. 2..-/1 ,3)* ), / , /--3%0 ), 2..-/1 ,3)* / 2..-/1 )512/% %& Figure 2 -& 6 - *% 1/-,) 0 -/.-1)-, %3