27E126 TE Connectivity

Signal Signal Relays Potter & Brumfield Sockets & Accessories, R10 Relays n Sockets for 2 - 6 pole relays n Solder, PCB or screw terminal sockets n Choice of grounding provision on sockets n Hold down springs n Plates and brackets permit various mounting options Ordering Code Approvals Product Poles Terminal type Grounding Part UL E59244, CSA LR15734 Code provision number Technical data of approved types on request 27E125 2 solder terminals strip 1393143-8 27E126 4 1393143-9 Technical Data 27E127 6 1-1393143-0 Socket contact material Spring brass, tin plated 27E162 2 none 1-1393143-6 Socket body material 27E163 4 1-1393143-7 2 and 4 pole models Polyester 27E164 6 1-1393143-8 6 and 8 pole models Phenolic 27E128 2 PCB terminals,.180 strip 1-1393143-1 Maximum current 10A 27E129 4 (4.57mm) long, 1-1393143-2 Voltage drop 30mV max. at 10A 27E130 6 staggered layout 1-1393143-3 Dielectric strength 1,000Vrms 27E212 2 none 2-1393143-4 9 Insulation resistance 10 meg 27E213 4 2-1393143-5 27E271 6 3-1393143-1 27E193 2 terminal 2-1393143-1 27E194 4 2-1393143-2 Solder and PC terminal sockets 27E636 2 PCB terminals, 210 strip 5-1393143-0 Rugged, molded socket body retains floating terminals of either solder or 27E637 4 (5.33mm) long, 5-1393143-1 printed circuit pin configuration. PC terminal sockets are offered with pins in staggered layout either 0.1 (2.54mm) grid or in-line arrangement. 27E342 2 PCB terminals,.180 none 3-1393143-6 27E629 4 (4.57mm) long, 4-1393143-8 27E630 6 in-line layout 4-1393143-9 All accessories must be ordered separately. Grounding provisions Pre-installed on sockets Not for use at 5A AC and above. Grounding Strip: Mounting stud of relay contacts grounding strip. Grounding strip is grounded with screw or rivet through round hole in socket. Grounding Terminal (PC sockets only): Mounting stud of relay contacts ground terminal through square hole in socket. Caution: Strip Terminal Printed circuit sockets are manufactured with floating (loose) terminals. This permits them to align with holes in the circuit board and with the relay termi- nals. During the mounting and soldering of the socket, vertical float should be eliminated and the terminals seated on the board. (This may be accomplished by inserting a dummy relay in the socket.) Failure to eliminate float may cause fracture of the solder joint or separation of the copper conductor from the printed circuit board when a relay is inserted in the socket after soldering. 161 10-2012, Rev. 1012 Catalog and product specification according Catalog and product data is subject to the Catalog product data, Definitions section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are 2012 Tyco Electronics Corporation, with the Definitions section. the Definitions section, available at subject to change. a TE Connectivity Ltd. company. Signal Signal Relays Potter & Brumfield Sockets & Accessories, R10 Relays (Continued) Dimensions PCB layout Solder and PC terminal sockets Sockets with staggered PC terminals 2 POLE .978 (24.84) .175 .500 .750 4 POLE 1.184 (30.07) (4.45) (12.70) (19.05) 6 POLE 1.390 (35.31) .100 .210 .350 (5.33) (2.54) A 6 (8.89) GRID 4 POLE POLE .032 .065 .330 (.81) .500 (1.65) 2 (8.38) B (12.70) .090 .235 POLE (2.29) (5.97) .045 x .090 .625 HOLES .100 (1.14 x 2.28) (15.88) + .004 .150 DIA. (2.54) .056 CLEARANCE (3.81) - .000 .450 PC Socket Dim. Dim. HOLE FOR + .10 HOLE FOR GROUND RELAY MNTG. T erm. Length A B 1.42 (11.43) ( ) TERMINAL (IF REQD.) - .00 STUD & .180 in .180 .115 GROUND (4.57) (2.92) .312 SPRING 2 POLE .210 in .210 .156 (7.92) (5.33) (3.96) .519 .120 DIA. 4 POLE (13.18) HOLE .165 .010 .725 (3.05) 6 POLE (4.19) ( ) .25 (18.42) TOLERANCES UNLESS OTHERWISE SH OWN Sockets with inline PC terminals .210 (5.33) .530 .320 .420 (13.46) PCB layout (top view) (10.67) (8.13) .400 .550 Sockets with solder terminals .110 (10.16) (13.97) (2.79) HOLES + .004 .450 DIA056 - .000 (11.43) + .10 1.42 ( ) - .00 .281 2 POLE .343 (8.71) 4 POLE .562 (14.27) (7.14) 6 POLE .781 (19.84) 2 HOLES ++ .109 DIA. (2.77) .140 (3.56) .354 .281 .015 (8.99) (7.14 .38) .656 .015 (16.66 .38) 162 10-2012, Rev. 1012 Catalog and product specification according Catalog and product data is subject to the Catalog product data, Definitions section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are 2012 Tyco Electronics Corporation, with the Definitions section. the Definitions section, available at subject to change. a TE Connectivity Ltd. company.