Application Specification Box Header Assemblies and Receptacle Connectors with Contacts on 1.90 mm 114-9013 .075 in. and 2.54 mm .100-in. Centerlines 18 MAY 15 Rev B NOTE All numerical values are in metric units with U.S. customary units in brackets . Dimensions are in millimeters and inches . Unless otherwise specified, dimensions have a tolerance of 0.13 .005 and angles have a tolerance of 2. Figures and illustrations are for identification only and are not drawn to scale. 1. INTRODUCTION This specification covers the requirements for application of .075 and .100 Box Pin Header Assembly and Receptacle Connector Components which are designed for printed circuit (pc) board and panel-mount applications. Headers and receptacles are available with various contact positions and pc board mounting patterns. All are designed to be installed by hand. Each header and receptacle has mounting holes that will accept commercially available hardware such as rivets, screws, bolts and nuts, or specially designed TE Connectivity (TE) hardware. See Figure 1 for typical product features that will be referred to throughout this text. The illustrations present a composite of available mounting options and typical headers and receptacles. They do not depict actual applications or all header and receptacle styles. Pin header assemblies and receptacle connectors are available with a variety of contact tail arrangements to meet various application requirements. Each is available with one of four types of contact tails: (1) solder tines, (2) wrap-type posts, (3) solder eyelets, and (4) crimp wire barrels (2.54 mm .100 in. headers and receptacles only). Wrap-type posts are available as 0.25 x 0.51 mm .010 x .020 in. posts for solder or single wire application, and 0.64 x 0.64 mm .025 x .025 in. posts for up to 3 wire applications. The crimp-type pin and receptacle contacts are designed for crimping of individual wires. Straight-through contacts can be removed and replaced from unsealed connectors. Right-angle contacts are permanently retained in the housing and damage to these contacts will require replacement of the header or receptacle. To avoid damage or any contact tails, TE recommends that the headers and receptacles remain in their packaging container until ready for use. See Figure 2 for available contact styles. When corresponding with TE Personnel, use the terminology provided in this specification to facilitate inquiries for information. Basic terms and features of this product are provided in Figures 1 and 2. Solder Tine Mounting Type Contact Flange PC Board Mounting Hole Polarizing Slot Wrap-Type Marking for Post Contact External Keying Receptacle Connectors Pin Header Connectors Mounting Hole Polarizing Rib Polarizing Rib Polarizing Jackscrew Groove Polarizing Groove Figure 1 2015 TE Connectivity family of companies PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. 1 of 14 All Rights Reserved For latest revision and Regional Customer Service, *Trademark visit our website at www.te.com. TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product, and/or company names may be trademarks of their respective owners. 114-9013 Socket (Ref) Pin (Ref) Locking Lance Solder Wire Eyelet Barrel Locking Locking Lance Locking Lances Lance Insulation Barrel Post 0.64 x 0.64 Solder 0.25 x 0.51 .025 x .025 .010 x .020 Solder Crimp-Type Solder-Type Wrap-Type Eyelet-Type Contact Contact Contact Contact Figure 2 2. REFERENCE MATERIAL 2.1. Revision Summary Updated document to corporate requirements Updated complete document Added new information to tables in Figures 9 and 13 and Paragraph 3.7.C 2.2. Customer Assistance Reference Product Base Part Number 531838 and Product Code 5365 are representative of Box Header Assemblies and Receptacle Connectors with Contacts on 1.90 x 2.54 mm .075 and .100-in. Centerlines. Use of these numbers will identify the product line and help you to obtain product and tooling information. Such information can be obtained through a local TE Representative, by visiting our website at www.te.com, or by calling PRODUCT INFORMATION or the TOOLING ASSISTANCE CENTER at the numbers at the bottom of page 1. 2.3. Drawings Customer Drawings for product part numbers are available from the service network. If there is a conflict between the information contained in the Customer Drawings and this specification or with any other technical documentation supplied, the information contained in the Customer Drawings takes priority. 2.4. Manuals Manual 402-40 can be used as a guide to soldering. This manual provides information on various flux types and characteristics with the commercial designation and flux removal procedures. A checklist is included in the manual as a guide for information on soldering problems. 2.5. Specifications Product Specification 108-9003 provides product performance and test results. 2.6. Instructional Material Instruction sheets (408-series) and customer manuals (409-series) provide product assembly instructions or tool setup and operation procedures. Documents available that pertain to this product are: Document Number Document Title 408-6623 1001 Series Box Connectors (Using Crimp, Snap-In Contacts) 408-6624 Box Connector Jackscrew Assemblies 408-6626 Clinching Tool 91117-3 408-6627 Clinching Tool for 3-Row Box Connectors 408-6660 Extraction Tools 408-7328 750, 751, 1000, and 1001 Series In-Line Box Connectors 408-7335 1000 Staggered Series Box Connectors 408-7424 Checking the Terminal Crimp Height or Gaging the Die Closure 2 of 14 Rev B