SPECIFICATION CONTROL DRAWING 55PC0812 TITLE Date Revision WIRE, RADIATION-CROSSLINKED, MODIFIED ETFE-INSULATED, NORMAL WEIGHT, GENERAL PURPOSE, 600 VOLT 1-17-12 D This specification sheet forms a part of the latest issue of Raychem Specification 55PC. INSULATION - RADIATION - CROSSLINKED, CONDUCTOR - SILVER-COATED COPPER MODIFIED ETFE CONSTRUCTIONDET AILS FINISHED WIRE CONDUCTOR DIAMETER DIAMETER WEIGHT (in.) PART WIRE CONDUCTOR MAXIMUM (in.) (lbs/1000 ft.) NUMBER SIZE STRANDING RESISTANCE LOWER UPPER LOWER UPPER UPPER 1/ (AWG) (number x AWG) AT 20C TARGET TARGET TARGET SPEC SPEC SPEC SPEC SPEC (ohms/1000 ft.) VALUE VALUE VALUE LIMIT LIMIT LIMIT LIMIT LIMIT 55PC0812-26-* 26 19 x 38 .0175 .0183 .0191 38.4 .0366 .0385 .0404 1.55 1.70 55PC0812-24-* 24 19 x 36 .0225 .0233 .0241 24.3 .0416 .0435 .0454 2.18 2.34 55PC0812-22-* 22 19 x 34 .0285 .0293 .0301 15.1 .0476 .0495 .0514 3.12 3.30 55PC0812-20-* 20 19 x 32 .0365 .0375 .0385 9.19 .0561 .0580 .0599 4.64 4.85 55PC0812-18-* 18 19 x 30 .0452 .0464 .0476 5.79 .0659 .0680 .0701 6.94 7.27 55PC0812-16-* 16 19 x 29 .0514 .0527 .0538 4.52 .0737 .0760 .0783 8.80 9.17 55PC0812-14-* 14 19 x 27 .0644 .0659 .0674 2.88 .0896 .0920 .0944 13.50 13.99 55PC0812-12-* 12 37 x 28 .0825 .0845 .0865 1.90 .1076 .1105 .1134 20.45 21.08 55PC0812-10-* 10 37 x 26 .1050 .1070 .1090 1.19 .1290 .1330 .1370 31.73 32.78 55PC0812-8-* 8 133 x 29 .158 .163 .169 .658 .188 .196 .203 56.8 59.9 55PC0812-6-* 6 133 x 27 .198 .205 .212 .418 .233 .242 .251 89.7 94.7 55PC0812-4-* 4 133 x 25 .250 .260 .268 .264 .300 .311 .322 146. 154. 55PC0812-2-* 2 665 x 30 .320 .330 .340 .170 .370 .383 .397 227. 240. 55PC0812-1-* 1 817 x 30 .360 .370 .380 .139 .408 .423 .438 278. 288. 55PC0812-0-* 0 1045 x 30 .395 .415 .425 .108 .449 .466 .483 343. 366. 55PC0812-00-* 00 1330 x 30 .440 .462 .475 .085 .505 .525 .545 450. 481. Users should evaluate the suitability of this product for their application. Specifications are subject to change without notice. Tyco Electronics Corporation also reserves the right to make changes in materials or processing, which do not affect compliance with any specification, without notification to Buyer. 1/ COLORS AND COLOR CODE DESIGNATORS SHALL BE IN ACCORDANCE WITH MIL-STD-681. OTHER CODES AND SUFFIXES MAY BE ADDED TO THE PART NUMBER. AS NECESSARY, TO CAPTURE ANY ADDITIONAL REQUIREMENTS IMPOSED BY THE PURCHASE ORDER. Raychem, TE Connectivity, TE connectivity (logo) and TE (logo) are trademarks. Raychem Wire & Cable 501 Oakside Avenue DIMENSIONS ARE IN INCHES, AND UNLESS OTHERWISE DESIGNATED ARE NOMINAL. Redwood City, CA 94063-3800 Page 1 of 2 Phone: 1-800-227-8816 THIS SPECIFICATION SHEET TAKES PRECEDENCE OVER DOCUMENTS REFERENCED HEREIN. Fax: 1-650-361-6297 REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID. 2009-2012 Tyco Electronics Corporation,. All rights reserved.Revision SCD Page 2 of 2 D 55PC0812 SPECIFICATION CONTROL DRAWING WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 200C Maximum continuous conductor temperature VOLTAGE RATING: 600 volts (rms) at sea level COLOR: White preferred CROSSLINK VERIFICATION: 300 3C for 1 hour IDENTIFICATION AND COLOR STRIPING DURABILITY: 125 cycles (250 strokes) (minimum). 500 g weight. INSULATION ELONGATION AND TENSILESTRENGTH: Total Insulation, Elongation, 50% (minimum) Tensile Strength, 5000 lbf/in (minimum) INSULATION FLAWS: Spark Test, 3.0 kV (rms) Impulse Dielectric Test, 8.0 kV (peak) INSULATION THICKNESS: .010 in. (nominal) total insulation SHRINKAGE: 230 3C for 1 hour, 0.125 inch (maximum) in 12 inches. VOLTAGE WITHSTAND (Post Environmental): 2500 volts (rms) PART NUMBER: The * in the part numbers on page 1 shall be replaced by a color code designator, 1/ Example: AWG 22, white: 55PC0812-22-9 AWG 22, white with black stripe: 55PC0812-22-90 1/ See footer section on page 1