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igure 1 PROCRIMPER III Hand Tool Assembly 584991 consists of PROCRIMPER III Hand Tool Frame 3549401 and Die Assembly 584831. The tool assembly is used to crimp the ferrule of the For additional information on the hand tool frame, connectors listed in Figure 1. In this use, the die refer to 4089930. Refer to the applicable connector assembly does not provide for crimping of the center instruction sheet for assembly of the connector. contact. Read these instructions thoroughly before using the Reasons for reissue of this instruction sheet are tool assembly. provided in Section 8, REVISION SUMMARY/9)54:8522+**5) 3+4:/99 (0+)::5).4-+ )5 2+):854/)9 58658:/54 88/9( 8- 5, 22 4:+84:/542 /-.:9 +9+8<+* % 582:+9:8+</9/544+-/542 9:53+8 +8</)+ 25-54* )5 2+):854/)98+:8*+3819 </9/:5 8=+(9/:+:333 24/),)20/.+1 /- 8*+381 :.+8685* ):9 25-59 4*)5364 43+9 9+*8+:.+6856+8: 5,:.+/88+96+):/<+5=4+89 ) ** ++ . -&,% & ++ . & & ) Make sure that the center contact is properly crimped The tool frame features a stationary jaw and handle, a and assembled onto the connector as described in moving jaw, a moving handle, and an adjustable applicable connector instruction sheet. Then proceed ratchet that ensures full crimping. The tool frame as follows: holds the die assembly. 1. Slide the ferrule over the cable braid until it is The die assembly consists of an indenter (stationary positioned against the shoulder of the plug body. die) and an anvil (moving die). When closed, the dies 2. Close the tool handles until the ratchet releases, form three crimping chambers. Each die is held in the then allow the handles to open FULLY. hand tool frame by a single screw. 3. Place the ferrule in the appropriate crimping chamber on the anvil die so that the shoulder of the plug body is close to the edge of the die. Refer to Figure 3. & 1. Close the tool handles until the ratchet releases, then allow the handles to open fully. 2. Insert the dies into the tool jaws as shown in Figure 2, and align the retaining holes in each die with the associated hole in the tool. ( % & & ) % Figure 3 4. While holding the assembly, close the tool handles until the dies hold the ferrule in place. % 5. Carefully close the tool handles until the ratchet ( releases, then allow the handles to open FULLY. 6. Remove the ferrule from the dies. Figure 2 7. Inspect the crimped ferrule according to applicable connector instruction sheet. If 3. Thread, but do not tighten, the die retaining necessary, adjust the ratchet as described in screws into the holes. Section 5. & 4. Carefully close the tool handles, making sure that the dies align properly. The tool ratchet mechanism features an adjustment wheel with numbered settings. The adjustment wheel 5. Tighten the die retaining screws with the controls the amount of handle pressure exerted on appropriate hex wrench. the jaws during crimping. If the crimp is not acceptable, adjust the ratchet as follows: 6. To disassemble, close the tool handles until the ratchet releases, remove the two die retaining 1. Remove the lockscrew from the ratchet screws, and slide the dies out of the tool jaws. adjustment wheel. ) % %