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igure 1 Reasons for reissue are provided in Section 9, REVISION SUMMARY. PROCRIMPER III Hand Crimping Tool Assembly 585581 consists of Die Assembly 585582 and 0.<9,: (5+ PROCRIMPER III Hand Crimping Tool Frame 3549401. The hand tool assembly is used to crimp The hand tool assembly features a tool frame with a Consumer RF Series BNC Plug Connectors onto stationary jaw and handle, a moving jaw, a moving various sizes of RG/U cable. handle, and an adjustable ratchet that ensures full contact crimping. The tool frame holds a die assembly For additional information on the hand tool frame, with four crimping chambers. The die assembly refer to 4089930. features an indenter die and an anvil die. Attached to the outside of the frame is a locator and Read these instructions thoroughly before using the straightener assembly, which properly positions and hand tool assembly. holds the connector center contact during crimping. Die retaining pins and die retaining screws are used to position and secure the dies in the tool frame. A nut is used on the upper die retaining screw to hold the locator and straightener assembly in place. /0:*65 9633,++6*<4,5 0::<)1,* 6*/(5., *6 3,* 9650*: 69769( 065 (990:)<9. 6- 33 5 ,95( 065(3 0./ ,:,9=,+ % 693( ,: 9,=0:065(5,.065(3 <: 64,9 ,9=0*, 36.6(5+ *6 3,* 9650*:(9, 9(+,4(92: =0:0 6<9>,):0 ,( ,,, +- +)& * % 9(+,4(92 /,9796+<* : 36.6: (5+*647(5 5(4,:<:,+(9, /,7967,9 6- /,099,:7,* 0=,6>5,9: * &) ((% +& %, % % Figure 2 engaged sufficiently to hold the dies in place, then tighten both die retaining screws. 1. Close the tool handles until the ratchet releases, then allow the handles to open fully. 2. Remove the two die retaining screws from the 6. Attach the straightener onto the spring retainer tool jaws. with the adjustment screw. Insert the spring into the spring retainer and place the locator over the 3. Install the anvil die in the movable jaw of the tool spring. frame. Insert the short die retaining screw through the retaining hole in the jaw and through the anvil 7. While holding the locator against the spring die. Tighten the screw just enough to hold the die retainer, place the screw hole in the spring retainer in place. Do not tighten the screw completely at over the end of the long die retaining screw. The this time. locator should be against the side of the tool jaw. 4. Install the indenter die in the stationary jaw of 8. Place the nut onto the end of the long die the tool frame. Insert the long die retaining screw retaining screw and tighten the nut enough to hold through the retaining hole in the jaw and through the locator and straightener assembly in place, but the indenter die. Tighten the screw just enough to still allowing the locator to slide up and down. hold the die in place. Do not tighten the screw 9. To disassemble, close the tool handles until the completely at this time. ratchet releases. Remove the nut, the locator and 5. Carefully close the tool handles, making sure straightener assembly, and the two die retaining that the dies align properly. Continue closing the screws. Slide the anvil and indenter out of the tool tool handles until the ratchet in the tool frame has jaws. &