Instruction Sheet Pistol Grip Manual Handle Assembly 408-6790 58074-1 28 MAR 11 Rev C PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available. For details concerning the termination procedure, NOTE Key (Visible on Body refer to the instructions included with the head. Ratchet this Side) Pawl i 3. HEAD INSTALLATION AND REMOVAL 1. Position the blade tip of a screwdriver between the shoulder of the key and the handle assembly body. Pry and remove the key. 2. Squeeze the cam handle until the ratchet releases, then allow it to FULLY open. 3. Insert the terminating head into the head entrance until the head bottoms. See Figure 2. Make sure that the head is FULLY bottomed in the NOTE handle assembly before re-inserting the key. Cam i Handle Head Figure 1 1. INTRODUCTION Pistol Grip Manual Handle Assembly 58074-1 accepts interchangeable terminating heads that terminate Head Entrance wires to connectors. To ensure accurate termination of wires, setup adjustments, and head maintenance, refer to the instructions packaged with the terminating head. Key Removed Dimensions in this instruction sheet are in metric NOTE units with U.S. customary units in brackets . Figures are not drawn to scale. i Reasons for reissue of this instruction sheet are Cam Handle Fully Opened provided in Section 6, REVISION SUMMARY. 2. DESCRIPTION The manual handle assembly features a cam handle, Figure 2 a key, and a ratchet pawl. The head is secured in the handle assembly with the key. 4. Re-insert the key to retain the head. Apply enough pressure to fully insert the key into the After the head is properly installed in the handle manual assembly. assembly, the cam handle actuates the terminating mechanism inside the head. The ratchet pawl is used 5. To remove the head, remove the key and pull the to release the handle before it is fully closed. head out of the handle assembly. 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. 1 of 3 All Rights Reserved PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, visit our website at www.te.com TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. LOC B *Trademark. Other logos, product and/or Company names may be trademarks of their respective owners. 408-6790 4. MAINTENANCE AND INSPECTION 4.2. Periodic Inspection It is recommended that a maintenance and inspection 1. Remove any accumulated film with a suitable program be performed periodically to ensure cleaning agent that will not affect plastic material. dependable and uniform terminations. Though 2. Make sure all components are in place and are recommendations call for at least one inspection a properly secured. Check the handle assembly for month, frequency of inspection depends on: chipped, cracked, worn, or broken areas. If damage 1. The care, amount of use, and handling of the is evident, repair is necessary. See Section 6, handle assembly. REPLACEMENT AND REPAIR. 2. The presence of abnormal amounts of dust and 5. REPLACEMENT AND REPAIR dirt. Customer-replaceable parts are listed in Figure 3. 3. The degree of operator skill. A complete inventory can be stocked and controlled to 4. Your own established standards. prevent lost time when replacement of parts is necessary. Parts other than those listed should be The handle assembly is inspected before being replaced by Tyco Electronics Corporation to ensure shipped however, it is recommended that the handle quality and reliability of the handle assembly. Order assembly be inspected immediately upon arrival to replacement parts through your representative, or call ensure that the handle assembly has not been 1-800-526-5142, or send a facsimile of your purchase damaged during shipment. to 717-986-7605, or write to: 4.1. Daily Maintenance CUSTOMER SERVICE (038-035) Each operator should be aware of, and responsible TYCO ELECTRONICS CORPORATION for, the following: PO BOX 3608 1. Remove dust, moisture, and other contaminants HARRISBURG PA 17105-3608 with a clean brush, or soft, lint-free cloth. DO NOT For customer repair service, call 1-800-526-5136. use objects that could damage the handle assembly. 6. REVISION SUMMARY 2. Ensure that all components are in place and Since the previous release of this instruction sheet, properly secured. the new company logo has been applied. 3. With the terminating head in place, squeeze and release the cam handle to ensure that the mechanisms move smoothly. 4. Depress and release the spring-loaded ratchet pawl to ensure that the pawl moves freely. 5. Check the extension springs to ensure they are properly located and are not deformed. Rev C 2 of 3