7<= >,=287 1..= -& 0*,/*-( ..+ 11, +5 4*2) * 11, +5 . >6>5*=2 . *>6* 2<8 -. <,*7 .<>5=/ 86=1.9 85870.-><.8/6*7>*55B98 -1*7-=885< *7-=885<* .27=.7-.-/8 8,,*<287*5><.*7-58 85>6 . *9952,*=287< 2-.<.5.,=2878/98 -*9952,*=287.:>296.7=/8 .A=.7-.- ><. 9 8->,=28789. *=287<2<* *25*+5. 8,*=8 <<.6+5B =*=287* B >9952.- 2=1 2. * <<.6+5B *,48/ 885 &2 . 2-. 87=8/ 885 8,*=8 2-. 2 8= 27 *7- 2. <<.6+5B 269270 885 *6. 8 270 * *=,1.= -3><=6.7= &1..5 =*=287* B *7-5. 1. *7- 269270 8852<*C 866. ,2*5 0 *-.=885*7- 8 270 2<-.<207.-9 26* 25B/8 /2.5-27<=*55*=287 .9*2 6*27=.7*7,. 8 4 8 *7-5. 9 8=8=B92702727-><= 2*5 ,866. ,2*5 8 27<=2=>=287*5*9952,*=287< 8->,= , 269.- 2=1=12<=885 2556..==1., 2691.201= .:>2 .6.7=/8 1*7-=885<27 =1.*99 89 2*=. *9952,*=287<9.,2/2,*=287 +>=6*B78=,8695B 2=18=1. /.*=> .9* *6.=. <8/=1.<9.,2/2,*=287 B,8 5.,= 872,<8//. <* * 2.=B8/ =885<=8<*=2</BB8> 9. /8 6*7,:>2 .6.7=< 8 *--2=287*527/8 6*=287 ,87=*,==1. 885270 <<2<=*7,7=. *= *0 .-2 %2 -13+ 2*.- *6 20*/ -(2) * 11, +5 .% 2.0 11, +5 ,*+5 * ,20 ,, ,, -%)1 ,, -%)1 % . 2.< 87=*,=< ( ) ( ) 87=*,==1. 885270 <<2<=*7,7=. 8 8->,= 7/8 6*=287 .7=. >9952.- 2=1-2.*<<.6+5B *5<8* *25*+5.<.9* *=.5B +.58 /8 <9.,2/2,,87=*,=9* =7>6+. < Figure 1 Read these instructions thoroughly before crimping any contacts. PROCRIMPER III Hand Crimping Tool Assembly 585831 consists of Die Assembly 585832 and PROCRIMPER III Hand Crimping Tool Frame 3549401. The die assembly consists of crimping dies and a locator assembly. 12<,87= 855.--8,>6.7=2<<>+3.,==8,1*70. B,8 5.,= 872,< 8 98 *=287 * 2<+> 0 8/ 55 7=. 7*=287*5 201=.<- % 8 5*=.<= . 2<287*7.0287*5 ><=86 2,. 5808*7- B,8 5.,= 872,<* .= *-.6* 4< 2<2=8> .+<2=.*=444 25%.+%20.-*%1 %., *-.6* 4 =1. 9 8->,=< 5808< *7-,869*7B7*6.<><.-* .=1.9 89. =B8/=1.2 .<9.,=2 .8 7. < & ) %( ** % + % &% ) % % & % % & % % ( Figure 2 & 4. Insert the short die retaining screw through the jaw and through both anvil dies, and tighten the The tool features a tool frame with a stationary jaw screw just enough to hold the dies in place. Do not and handle, a moving jaw, a moving handle, and an tighten the screw completely at this time. adjustable ratchet that ensures full contact crimping. 5. Place the wire crimper and insulation crimper so The tool frame holds a die assembly with three that their chamfered sides and their marked crimping chambers. The die assembly features a wire surfaces face outward, when mounted in the anvil, an insulation anvil, a wire crimper, and an stationary jaw of the tool frame. insulation crimper. 6. Insert the two die retaining pins. Attached to the outside of the frame is a locator 7. Insert the long die retaining screw through the assembly, which contains a locator, a spring retainer, jaw and through both crimper dies, and tighten the and a contact support. screw just enough to hold the dies in place. Do not tighten the screw completely at this time. Die retaining pins and die retaining screws are used 8. Carefully close the tool handles, making sure to position and secure the dies in the tool frame. A that the anvils and crimpers align properly. nut is used on the upper die retaining screw to hold Continue closing the tool handles until the ratchet the locator assembly in place. in the tool frame has engaged sufficiently to hold the anvils and crimpers in place, then tighten both die retaining screws. & 9. Place the locator assembly over the end of the long screw, and position the locator assembly 1. Open the tool handles and remove the two die against the side of the tool jaw. retaining screws from the tool jaws. 10. Place the nut onto the end of the long screw 2. Place the wire anvil and insulation anvil so that and tighten the nut enough to hold the locator their chamfered sides and their marked surfaces assembly in place, while still allowing the locator to face outward, when mounted in the moving jaw of slide up and down. the tool frame. 11. To disassemble, close the tool handles until the 3. Insert the two die retaining pins. ratchet releases, remove the nut, the locator ) % %