CC2619-000 TE Connectivity

CUSTOMER DRAWING L1 A* Size Range Wire Strip Product L2 B 2 Color Marking mm 1.50 (a) (b) Length Name min min (AWG) min max Nom. 0.06) 0.15 0.25 31.5 5.0 3.00 1.40 1.09 6 to 8 D-406-0034 Yellow DURASEAL 24-26 (26 - 24) 1.24 0.20 0.118 0.055 0.043 (1/4 to 5/16) 0.5 - 1.0 31.5 5.0 3.70 1.40 1.47 6 to 10 D-406-0001 Red DURASEAL 18-22 (22 - 18) 1.24 0.20 0.146 0.055 0.058 (1/4 to 3/8) 1.5 - 2.5 31.5 5.0 4.60 2.00 2.33 6 to 10 D-406-0002 Blue DURASEAL 14-16 (16 - 14) 1.24 0.20 0.181 0.080 0.092 (1/4 to 3/8) 3.0 - 6.0 37.5 10.0 6.50 2.80 3.50 10 to 13 D-406-0003 Yellow DURASEAL 10-12 (12 - 10) 1.48 0.39 0.255 0.110 0.138 (3/8 to 1/2) MATERIALS 1. INSULATION SLEEVE: Heat-shrinkable, radiation cross-linked polyamide (Nylon) with a polyamide-based hot-melt adhesive liner. See above table for applicable sleeve color. 2. CRIMP SPLICE: Tin-plated copper alloy. BASE METAL: Copper alloy C11000 per ASTM B152. PLATING: Tin-plated per ASTM B545, Class A. APPLICATION 1. These parts may be used to obtain an environment-resistant one-to-one in-line (butt) splice in wires meeting the size range and diameter restraints specified herein and having a temperature rating of not less than 85C. 2. * A: (a) Minimum diameter as received: Wire insulation diameter must be less than this value. (b) Maximum diameter after recovery: Wire insulation diameter must be larger than this value to obtain an environment resistant splice. 3. Wires are to be stripped per table, inserted into opposite ends of the crimp barrel, crimped with a TE Connectivity AD-1522 (22-10 AWG) or equivalent. For D-406-0034, Pro-Crimper III with die set 1976357-1 (24-26 AWG) or equivalent may be used. The sleeve must be heated along its entire length until the crimp marks are gone and the ends of the sleeve recover onto the wires. 4. Spliced assemblies will meet the requirements of TE Connectivity / Raychem specification RB-107. 5. Except for D-406-0034, all of the parts covered by this drawing are UL Listed (US and CANADA), File E87681. TITLE: DURASEAL CRIMP SPLICE Raychem ENVIRONMENT RESISTANT Devices Unless otherwise specified dimensions are in millimeters. Inches dimensions DOCUMENT NO.: are shown in brackets . D-406-00XX TOLERANCES: ANGLES: N/A Tyco Electronics reserves the right to amend 0.00 N/A this drawing at any time. Users should evaluate REV.: REV DATE: 0.0 N/A ROUGHNESS the suitability of the product for their 13-Dec-2018 C3 0 N/A IN MICRON application. DRAWN BY: CAGE CODE: DRAWN DATE: ECO No.: SCALE: SIZE: SHEET: P. TALLY 06090 1/28/2008 ECO-18-019635 NTS A 1 of 1 2018 TE Connectivity Corporation. All rights reserved. If this document is printed it becomes uncontrolled. Check for the latest revision. X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Solder Sleeves & Shield Tubing category: Click to view products by TE Connectivity manufacturer: Other Similar products are found below : D-260-C-A 899170-000 620040N001 620069N003 620263N004 CTA-0050-01 629624-000 6501390002 CX0781-000 CX0782-000 696396-000 697080-000 715325N001 FLX40-030-02-CS8652 908357N001 D-436-38CS2908 CB0213-000 CB0219-000 274384-000 285343-000 970053-000 ST18-2-00 FLX40-020-04-CS8651 317035-000 325534-000 D-100-00-WOTI D-150-1011 395947-000 427243N001 514535-000 C03534-000 CB0220-000 D44133N001 068615-000 626168-000 451893-000 931289-000 162583-000 585769N001 610001N004 620005N003 6200060004 622041N003 626167-000 EG3678-000 650075N002 6500820003 6500850004 650126N010 650127N005