SO63-3-W2-24-00-100 TE Connectivity

Shield Termination SolderSleeve Shield Terminators Product Facts n Transparent insulation sleeve provides encapsulation, inspectability, strain relief, and insulation n Prefluxed solder preform provides a controlled soldering process n One-piece design offers easy installation and lower installed cost n Optional preinstalled ground leads provide convenience and ease of installation Product Selection Process Applications 1. Select product series 4. Select part number (use Used for shield-to-ground from the Product Options the selection table indi- termination. table below. cated for your product series in the Product 2. Determine cable Options table below). dimensions. 5. Refer to Table H on page 3. Optional: Select prein- 8-49 for cross-reference stalled wire lead type information. (see Table G on page 8-47 for type descriptions). Jacket OD (max.) Shield OD (min.) Product Options (Refer to Table G on Page 8-47 for Additional Information) System Oper. Used on Part No. Product Environmental Solder Flux Insulation Temperature Cables Rated Selection Series Protection Alloy Type Material (Max.) (Min.) Table CWT 125C 257F 85C 185F Splash resistant Cd18 RA Polyolefin A SO63* 150C 302F 125C 257F Immersion resistant Sn63 RMA Polyvinylidene fluoride B S01/S02**, S03 150C 302F 125C 257F Immersion resistant Sn63 RMA Polyvinylidene fluoride C, D SO96*** 175C 347F 150C 302F Immersion resistant Sn96 RA Polyvinylidene fluoride E SO175**** 175C 347F 150C 302F Immersion resistant Sn96 RA Polyvinylidene fluoride F *Meets performance requirements of SAE-AS83519 (formerly MIL-S-83519) and NAS 1747, supplied with BiAlloy temperature indicator. **Qualified to SAE-AS83519 (formerly MIL-S-83519), supplied with thermochromic temperature indicator. ***Meets performance requirements of SAE-AS83519 (formerly MIL-S-83519) and NAS 1747, supplied with thermochromic temperature indicator. ****Meets performance requirements of SAE-AS83519 (formerly MIL-S-83519), supplied with BiAlloy temperature indicator. Note: Cadmium-free option (B-152 series) is available for operating temperature of 125C 257F . Consult Tyco Electronics for details. Available in: Americas n Europe n Asia Pacific n 8-44 Catalog 1654025 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 12-04 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 www.tycoelectronics.com are U.S. equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-1793-528171Electrical Interconnect Products Shield Termination SolderSleeve Shield Terminators (Continued) Table A. CWT Series (125C 257F rated) Cable OD Part Nos. Jacket Shield No Preinstalled With Preinstalled Lead 2 OD Max. OD Min. Lead (22AWG/0.38 mm green) 1.7 .065 0.9 .035 CWT-3801 1.95 .075 1.1 .043 CWT-3802 2.7 .105 1.5 .059 CWT-3 CWT-3-W122-5 4.5 .180 2.0 .079 CWT-5 CWT-5-W122-5 6.0 .235 3.3 .130 CWT-6 CWT-6-W122-5 7.0 .275 3.3 .130 CWT-7 CWT-7-W122-5 8.7 .340 4.5 .177 CWT-9 CWT-9-W122-5 10.7 .420 4.5 .177 CWT-11 CWT-11-W122-5 13.0 .510 7.0 .276 CWT-13 CWT-13-W122-5 *See Table G on page 8-47 for lead description. Note: The CWT series is suitable for applications using low-temperature wires (typically rated at 85C 185F to 125C 257F ) with bare copper or tin plating. Table B. SO63 Series BiAlloy Temperature Indication System This system greatly enhances the reliability and repeatabil- ity of SO63 series terminators while reducing installed cost. The heat-shrinkable thermoplastic sleeve contains a pre- cisely engineered, fluxed solder band that is visible through the sleeve. The band provides exactly the amount of solder and flux required to terminate the ground lead to the cable shield. Encircling the band is a small temperature indicator ring. This ring melts only when the surfaces to be joined have reached the correct soldering temperature, thus 8 ensuring a properly soldered connection. Process control is built into each sleeve. Cable OD Part Nos. No Preinstalled Lead Option* Braid Strap Jacket OD Shield OD Preinstalled Max. Min. 20 AWG 22 AWG 24 AWG 26 AWG Nickel Plated Tin Plated Lead 1.95 0.075 0.90 .035 SO63-1-00 SO63-1-55-20-90 SO63-1-55-22-90 SO63-1-55-24-90 SO63-1-55-26-90 SO63-1-01 SO63-1-9030 2.7 0.105 1.40 .055 SO63-2-00 SO63-2-55-20-90 SO63-2-55-22-90 SO63-2-55-24-90 SO63-2-55-26-90 SO63-2-01 SO63-2-9030 4.3 0.170 2.15 .085 SO63-3-00 SO63-3-55-20-90 SO63-3-55-22-90 SO63-3-55-24-90 SO63-3-55-26-90 SO63-3-01 SO63-3-9030 6.0 0.235 3.30 .130 SO63-4-00 SO63-4-55-20-90 SO63-4-55-22-90 SO63-4-55-24-90 SO63-4-55-26-90 SO63-4-01 SO63-4-9030 7.0 0.275 4.30 .170 SO63-5-00 SO63-5-55-20-90 SO63-5-55-22-90 SO63-5-55-24-90 SO63-5-55-26-90 SO63-5-01 SO63-5-9030 *See Table G on page 8-47 for lead description. Color of wire lead is denoted by the last two digits of the part number as follows: 90 = White with a black stripe 9 = White 0 = Black 6 = Blue (24 AWG only) 5 = Green (20, 22, 24 AWG) The SO63 series is immersion resistant, features the Raychem BiAlloy temperature indication system, and meets the performance requirements of SAE-AS83519 (formerly MIL-S-83519) . 8-45 Catalog 1654025 Dimensions are in millimeters Dimensions are shown for USA: 1-800-522-6752 South America: 55-11-3611-1514 Revised 12-04 and inches unless otherwise reference purposes only. Canada: 1-905-470-4425 Japan: 81-44-900-5102 specified. Values in brackets Specifications subject Mexico: 01-800-733-8926 Singapore: 65-4866-151 www.tycoelectronics.com are U.S. equivalents. to change. C. America: 52-55-5-729-0425 UK: 44-1793-528171