Signal Relays AXICOM P1 Relay V23026 n Directly triggerable with TTL standard modules as ALS, HCT & ACT n Slim line 13.5x7.85mm (0.531x0.309) n Switching current 1 A n Bifurcated 1 form C (CO) contact n Immersion cleanable AXICOM n High sensitivity results in low nominal power consumption,Telecom-, Signal and RF Relays 65 to 108-98009 Rev. E 130mW for monostable and 30 to 150mW for bistable (latching) P1 V23026 Relay n Initial surge withstand voltage 2.5kV (2/10s) meets the Bellcore Requirement GR-1089 P1 THTSMD 1.5kV (10/160s) meets FCC Part 68 Contact Data Typical applications Automotive equipment, CAN bus, imobilizer, office equipment, measurement Number of contacts and type 1 changeover contact Z and control equipment, medical equipment, safety equipment Contact assembly Bifurcated contact Contact material Palladium nickel, gold-rhodium covered Approvals Coil Data Limiting continuous current at max. ambient temperature 1 A UL 508 File No. E 111441 Magnetic system polarized Coil voltage range 3 to 24VDC Technical data of approved types on request Maximum switching current 1 A other coil voltages on request Maximum swichting voltage 125 Vdc Operative range, IEC 61810 see coil operative range 150 Vac Contact Data Max. coil temperature 85C Contact arrangement 1 form C (CO) Thermal resistance <130K/W Maximum switching capacity 30 W, 60 VA Max. switching voltage 125VDC, 150VAC Rated current 1A Coil versions, THT, monostable Thermoelectric potential < 100 V Limiting continuous current, 85C 1A Coil Rated Operate Release Coil Rated coil Initial contact resistance / measuring condition: 10 mA / 20 mV < 50 m Breaking capacity max. see max. DC load br eaking capacity code voltage voltage voltage resistance power Contact material Palladium nickel, VDC VDC7 VDC 10% mW min. min. Electrical endurance at 12 V / 10 mA typ. 5 x 10 operations gold-rhodium covered 006 3 2.25 0.3 137 66 7 at 6 V / 100 mA typ. 1 x 10 operations Contact style bifurcated contact 001 5 3.75 0.5 370 68 4 at 30 V / 1000 mA typ. 1 x 10 operations Min. recommended contact load 10mA at 20mV 005 9 6.75 0.9 1165 70 Initial contact resistance 50m at 10mA/20mV 002 12 9.00 1.2 2250 34 9 FrMechanical enduranceequency of operation without load 200 ops./s 004 24 typ. 10 operations18.00 2.4 4500 128 Operate/release time max. 2ms All figures are given for coil without pre-energization, at ambient temperature +23C. UL contact ratings 30 Vdc / 1 A Set/reset time max. 2ms 65 Vdc / 0.46 A Bounce time max. 3ms Coil versions, SMT, monostable 150 Vac / 0.46 A Electrical endurance Coil Rated Operate Release Coil Rated coil 6 at 12V/10mA typ. 50x10 operations code voltage voltage voltage resistance power AXICOM 6 at 6V/100mA typ. 10x10 operations VDC VDC VDC 10% mW min. min. Telecom-, Signal and RF Relays 108-98009 Rev. E 3 at 30V/1000mA typ. 10x10 operations 026 3 2.25 0.3 113 80 Contact ratings 021 5 3.75 0.5 313 80 P1 V23026 Relay UL contact ratings, resistive load 30VDC/1A 025 9 6.75 0.9 1015 80 65VDC/0.46A 022 12 9.00 1.2 1800 80 150VAC/0.46A 024 24 18.00 2.4 4500 128 Max. DC Load Breaking Capacity 9 All figures are given for coil without pre-energization, at ambient temperature +23C. Mechanical endurance typ. 10 operations Coil Operating Range Max. DC load breaking capacity Coil operative range, monostable DC coil U = Nominal coil voltage nom 65 mW U = Upper limit of the operative range of max. 130 mW the coil voltage (limiting voltage) when coils are continously energized Umax. at 0 A U = Lower limit of the operative range of Umax. at 0 A Umax. at - 1 A op. min. the coil voltage (reliable operate voltage) U = Lower limit of the operative range of rel. min. the coil voltage (reliable release voltage) Unom. nominal coil voltage Uop. min. Urel. min. Ambient Temperature C 1 65 mW Latching Umax. - 5 % coil duty at 1 A 09-2020, Rev. 0920 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, Definitions sec - 32 mW Latching www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications 2011 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change. a TE Connectivity Ltd. company Signal Relays AXICOM P1 Relay V23026 (Continued) Coil data (continued) Insulation Data Initial dielectric strength Coil versions, THT and SMT, bistable 2 coils between open contacts 500V rms Coil Rated Set Reset Coil Rated coil between contact and coil 1500V rms code voltage voltage voltage resistance power Initial surge withstand voltage VDC VDC VDC 10% mW between contact and coil 2500V 106 3 2.25 2.25 130 69 Capacitance 101 5 3.75 3.75 390 64 between open contacts max. 5pF 105 9 6.75 6.75 1200 68 between contact and coil max. 6pF 102 12 9.00 9.00 1500 96 Clearance/creepage 1) 24 between contact and coil 0.75mm All figures are given for coil without pre-energization, at ambient temperature +23C. between adjacent contacts 0.75mm Coils I and II are identical. 1) A nominal voltage of 24VDC is feasible with a 12VDC coil with a series resistor (1500) RF Data Isolation at 100MHz/900MHz -30.0dB/-18.0dB Coil data (continued) Insertion loss at 100MHz/900MHz -0.12dB/-1.9dB Voltage standing wave ratio (VSWR) AXICOM Coil versions, THT, bistable 1 coil at 100MHz/900MHz 1.06/1.75 Telecom-, Signal and RF Relays 108-98009 Rev. E Coil Rated Set Reset Coil Rated coil code voltage voltage voltage resistance power P1 V23026 Relay VDC VDC VDC 10% mW Other Data 056 3 2.25 -2.25 300 30 Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content 051 5 3.75 -3.75 740 34 refer to the Product Compliance Support Center at 057 9 6.75 -6.75 2160 38 www.te.com/customersupport/rohssupportcenter Coil Operating Range 052 12 9.00 -9.00 4500 32 Ambient temperature -40 to +85C 054 24 18.00 -18.00 4500 128 Category of environmental protection, U = Nominal coil voltage nom IEC 61810 RT III - immersion cleanable 65 mW U V ibration r = esistance (functional)Upper limit of the operative range of 20g, 200 to 2000Hz max. 130 mW the coil voltage (limiting voltage) 40g, 10 to 200Hz Coil data (continued) Shock resistance (functional) when coils are continously energized Umax. at 0 A IEC 60068-2-27 (half sine) 50 g U = Lower limit of the operative range of Coil versions, SMTUmax. at 0 , bistable 1 coilA Umax. at - 1 A op. min.Terminal type PCB terminals and SMT terminals the coil voltage (reliable operate Coil Rated Set Reset Coil Rated coil Weight max. 2g voltage) code voltage voltage voltage resistance power Resistance to soldering heat THT VDC VDC VDC 10% mW IEC 60068-2-20 265 C/10s U = Lower limit of the operative range of rel. min. 051 5 3.75 -3.75 740 34 Resistance to soldering heat SMT the coil voltage (reliable release 052 12 9.00 -9.00 4500 32 IEC 60068-2-58 see reflow profile voltage) A nominal voltage of 24V is feasible with a 12V coil with a series resitor (4500) Moisture sensitive level, JEDEC J-Std-020D MSL3 Unom. nominal coil voltage Other coil voltages on request Washing not recommended All figures are given for coil without pre-energization, at ambient temperature +23C. Ultrasonic cleaning possible Coils I and II are identical. Uop. min. Packaging unit Urel. min. THT 2000 pcs. SMT 2400 pcs. Ambient Temperature C Coil operative range, bistable U upper limit of the operative range of the coil voltage (limiting voltage) when coils are max 65 mW Latching Umax. - 5 % coil duty at 1 A 32 mW Latching Umax. - 100 % coil duty at 0 A Umax. - 5 % coil duty at 0 A Unom. nominal coil voltage Uset min. Ambient Temperature C continuously energized. U lower limit of the operative range of the coil voltage (reliable operate voltage). op min U lower limit of the operative range of the coil voltage (reliable release voltage). rel min 2 09-2020, Rev. 0920 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, Definitions sec - www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications 2011 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change. a TE Connectivity Ltd. company