420 W 200 W 100 W 30 W Automotive Relays PCB Single Relays Micro Relay K (THT THR) Small power relay Limiting continuous current 20A at 85C Low weight Low noise operation Wave (THT) and reflow (THR/pin-in-paste) solderable versions Typical applications Door lock, heated front/rear screen, lamps front/rear/fog light, interior lights, seat control, sun roof, window lifter, wiper control. 086C/R1 fcw1b Contact Data Typical applications Inductive load Wiper load Resistive/inductive load Lamp load V23086-*1*01-A403 V23086-*1*02-A803 V23086-*1*01-A402 V23086-*1*51-A502 Contact arrangement 1 form C, 1 CO 1 form C, 1 CO 1 form A, 1 NO 1 form A, 1 NO Rated voltage 12VDC 10VDC 12VDC 10VDC NO/NC NO/NC 1) Rated current 30/25A 30/25A 30A 15A 1) Limiting continuous current 23C 30/25A 30/25A 30A 15A 85C 20/15A 20/15A 20A 10A 105C 15/10A 15/10A 15A 2) 2) 2) 3) Limiting making current 40A 40A 40A 100A Limiting breaking current 30A 30A 30A 30A Contact material AgSnO 2 4) Min. contact load >1A at 5VDC Initial voltage drop at 10A, typ./max. 30/300mV 5) Operate/release time typ. 3/1.5ms Electrical enduranc cyclic temperature -40C, +25C, +85C form C contact (CO) at 14VDC motor reverse blocked, wiper, 25A, 0.77mH 25A make/5A break, 5 >1x10 ops. generator peak, 20A on NC,1mH 6 >1x10 ops. form A contact (NO) at 14VDC resistive 20A lamp 100A inrush, 5 >3x10 ops. 10A steady state 5 >1x10 ops. 6 Mechanical endurance >5x10 ops. Max. DC load breaking capacity 2 1) Measured on 70x70x1.5mm epoxy PCB FR4 with 25cm (double layer 105m) 100 2 copper area. Connecting cable cross section 6 mm .Boundary conditions: 180C coil temperature 130C solder joint. 2) The values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5VDC for 12VDC load voltages. For a load current duration of maximum 3s for a make/break ratio of 1:10. 3) Corresponds to the peak inrush current on initial actuation (cold filament). 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at Automotive Relays PCB Single Relays Micro Relay K (THT THR) (Continued) Coil Data Other Data Rated coil voltage 12VDC EU RoHS/ELV compliance compliant Ambient temperature, DC coil -40 to +105C Coil versions, DC coil Cold storage, IEC 60068-2-1 1000h -40C Coil Rated Operate Release Coil Rated coil Dry heat, IEC 60068-2-2 1000h +125C code voltage voltage voltage resistance power Climatic cycling with condensation, VDC VDC VDC 10% mW EN ISO 6988 20 cycles, storage 8/16h 001/801 12 6.9 1.5 254 0567 Temperature cycling (shock), 002/802 10 5.7 1.25 181 0552 IEC 60068-2-14, Na 100 cycles -40/+125C 051/851 10 6.5 1.1 90 1111 Temperature cycling, All figures are given for coil without pre-energization, at ambient temperature +23C. IEC 60068-2-14, Nb 35 cycles -40/+125C Damp heat cyclic, Coil operating range IEC 60068-2-30, Db, variant 1 6 cycles 25C/55C/93%RH Damp heat constant, 300 IEC 60068-2-3 method Ca 56 days 40C/95%RH Degree of protection 250 Umax THT: RT III (61810), IP67 (IEC 60529) THR: RT II (61810), IP56 (IEC 60529) 200 Sealing test, IEC 60068-2-17: THT Qc, method 2, 1min, 70C Corrosive gas 150 IEC 60068-2-42 10 days IEC 60068-2-43 10 days 100 Vibration resistance (functional) 6) IEC 60068-2-6 (sine sweep) 10 to 500Hz 6g 50 Uop (E=0V) Shock resistance (functional) 6) IEC 60068-2-27 (half sine) 6ms, up to 30g 0 -40-20 020406080100 120 Terminal type PCB:THT, THR Ambient temperature in C Weight approx. 4g (0.14oz) Does not take into account the temperature rise due to the contact current Solderability (aging 3: 4h/155C) THT E = pre-energization IEC 60068-2-20 Ta, method 1, hot dip 5s, 215C Solderability THR IEC60068-2-58 hot dip 5s 245C Insulation Data Resistance to soldering heat THT Initial dielectric strength IEC 60068-2-20 Tb, method 1A, hot dip 10s, between open contacts 500VAC 260C with thermal screen rms between contact and coil 500VAC Resistance to soldering heat THR rms IEC 60068-2-58 260C preheating min 130C 7) Storage conditions according IEC 60068-1 Packaging unit 2000 pcs. 6) Depending on mounting position: no change in the switching state >10s. 7) For general storage and processing recommendations please refer to our Application Notes and especially to Storage in the Definitions or at