Specialty Relays Specialty Relays VTM2 Series, Off-Delay, Timing Module Timing Specifications Output Switch Data Input Data 25C Timing Mode Off-Delay Arrangement Solid state 1 Form A Line voltage with high inductive voltage (SPST-NO) noise could affect timer performance. Timing Ranges 0.5 to 10 / 3 to 60 Adding transorb or MOV at noise source sec. 3 to 60 min. Rating 1A steady state is recommended. Timing Adjustment External Expected Electrical Life Example: Contactor coils, motor resistor. An external resistance of 1 100,000,000 operations at rated load. megohm is required to obtain the Voltage (10%) 12 VAC/VDC, Initial Dielectric Strength maximum time for all ranges. To 24VAC/VDC, 120 VAC Between Terminals and Mounting determine the actual resistance needed 3,000VAC rms. Power Requirement 4.3VA max to obtain the required time delay, use Between Input and Output Transient Protection the following formula: 1,500VAC rms. Non-repetitive transients of the following magnitudes will not cause spurious operation of affect function and accuracy. Operating <0.1 ms <1 ms Voltage Accuracy Product Facts Repeat Accuracy 0.5% +8ms max 12, 860V* 208V* 24 VAC/VDC n Off-delay timing mode (0.25% typical) at constant temperature 120 VAC 2,580V 2,150V* for load of 10mA to 1A n Reliable solid state timing * Min. source impedance of 100 ohm. Maximum Time: 2% at Rt = 1 meg circuitry ohms Environmental Data n Excellent transient Minimum Time: +0%, -30% at Temperature Range protection Rt = 0 ohms Storage -40C to +85C Reset Time 300 ms, max. n Compact design Operating -40C to +60C Humidity 95% relative n Flame retardant, solvent 1.25 2.00 (31.8) resistant housing Mechanical Data (50.8) .885 Mounting Panel mount with one (22.5) n File E60363, File LR33434 8 screw. R Termination 0.250 in (6.35) quick R 2.00 connect terminals. (50.8) Weight 4 oz. (112g) approximately Note: Please check the weight and update accordingly. 12 .170 DIA (4.32) .250 (6.35) X .032 (.813) ACCEPTS 8 SCREW QUICK CONNECTS Outline Dimensions START POLARITY SHOWN SWITCH FOR DC An external resistance of 1 megohm MODELS is required to obtain the maximum time for all 1 5 ranges. To determine the actual resistance LOAD 7 6 needed to obtain the required time delay, use the R t following formula, for time between max and min 2 4 times: INPUT VOLTAGE 3 Wiring Diagram Note: Due to component tolerances, actual time obtained will normally be within 5% of desired time. Ordering Information VTM2 A CD Series VTM2 Input Voltage Time Range Off-Delay A = 120VAC CD = 0.5 - 10 sec. Timing Module E = 24VAC/VDC DD = 3 - 60 sec. Users should thoroughly review the Q = 12VAC/VDC GD = 3 - 60 min. technical data before selecting a product part number. It is recommended that user also seek out the pertinent approvals files of the agencies/laboratories and Authorized distributors are likely to stock the following: review them to ensure the product meets the requirements for a given application. None at present. PAGE 45X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Time Delay & Timing Relays category: Click to view products by TE Connectivity manufacturer: Other Similar products are found below : 5NO30 614-11B-0A2 614-11B-OA3 614-11B-OA4 614-11B-OA6 614-11B-OA8 614-11C-OA1 614-11C-OA2 614-11C-OA5 614-11Q- OA3 614-11Q-OA6 614-11T-OA3 614-11T-OA6 614-11T-OA7 614-12B-4A1 614-12C-400 614-12Q-400 614-12T-600 614-22T-4A1 614-43B-400 614-43C-100 614-43F-200 614-43Q-0A2 614-43Q-100 614-43Q-600 614-43T-0A9 614-43T-600 614-43U-400 614-43U-4A1 614-43U-6A2 615-21T-200 655-11T-100 655-11U-500 655-12T-300 655-22T-400 655-22T-600 CUA-41-30001 CUA-41-30030 CUA-41- 70180 CUA-41-71038 CUA-42-30005 CUA-42-30010 CUA-42-30120 CUA-42-70120 CUA-99-72502 CUC-41-30030 CUF-42-30010 CUH-41-31006 7012AFX 7012GD