RTD ANALOGUE TEMPERATURE CONTROLLERS SPECIFICATION TOS ON/OFF & PROPORTIONAL CONTROLLER Supply voltage: 110/230(220-240)Vac 50/60 Hz or 24Vac/dc Power drain: 4VA max. The TOS range of temperature controllers Scale accuracy: +/- 2% of full scale offer an extremely cost effective analogue Scale range: See part number below solution for simple on/off or proportional Input sensor: J, K, R or T thermocouple, 3-wire PT100 or 4-20mA control. Options for J/K thermocouples Max ext. resist: T/couple: 100 , PT100: 5 per wire and PT100 RTDs are available with either Control band: On/Off: Hyst. = 0.5% (1% TC486*) of full scale relay or SSR drive outputs. Propl: PB = 4% to 10% of full scale Cycle time: 20 secs (PD model only) Selectable on/off or proportional action Output rating: Relay: SPCO, 5A/240Vac resistive o Up to 1200 C scale ranges SSR: 30mA/24Vdc J, K T/couple or PT100 input options Electrical life: 100,000 ops at rated load Relay or SSR drive output options Deviation output: +/- 50 Amps o Ambient range: -10 to 50 C non-condensing SPECIFICATION Approvals: Conforms to CE emc EN50081-1 & EN50082-1 and Supply voltage: 90 to 264Vac/dc 50/60 Hz low voltage EN61010-1 directives Power drain: 3VA max. Weight: 200gms Scale accuracy: +/- 2% of FSD Scale range: See standard items below Part Numbering Options : TC48AB-CD-110/230VAC Input sensor: J or K thermocouple or PT100 - 3 wire Max ext. resist: T/couple: 100 , PT100: 5 per wire Control band: On/Off: Hysteresis = 0.5 +/- 0.2% of scale range A Control On/off 1 D Scale J, K 0 to 200C 1 Propl: Proportional band = 3% of scale range PD 3 J, K 0 to 400C 2 Output rating: Relay: 3A/240Vac resistive Latch 5 K 0 to 600C 3 SSR: 20mA/12Vdc On/off 4-20mA 6 K 0 to 800C 4 Electrical life: 100,000 ops at rated load B Action/ Rev/relay 0 K 0 to 1200 5 o Ambient range: -10 to 50 C non-condensing Output Dir/relay 1 T -100 to 200C 0 Weight: 180gms Rev/SSR 2 T -170 to 30C 6 Dir/SSR 3 R 0 to 1600C 0 CONNECTION DIAGRAM C Sensor K t/couple 0 PT100 -100 to 200C 0 - + J t/couple 1 PT100 -50 to 150C 1 SSR drive option T t/couple 2 PT100 0 to 100C 2 Thermocouple 4 R t/couple 3 PT100 0 to 200C 3 input 5 2 3 PT100 3 wire 5 PT100 -50 to 100C 4 - 4-20 mA 6 4-20mA 0 to 100% 6 6 2 N For other temperature ranges, please contact our sales office. 7 + 1 1 CONNECTION DIAGRAM 8 PT100 input Thermocouple input PT100 - + input L 0V 24V DIMENSIONS + 15 64 13 6 7 5 8 - 56 7 4 SSR or 9 - Relay 4-20mA input Panel 3 10 N + cut-out sensor -0 2 - 11 45x45 +0.5 1 110Vac 4-20mA 230Vac(or 24Vac) + 567 DIMENSIONS STANDARD ITEMS 48x48 15 74 17 Input Output Range Part Number o J T/c Relay 0 to 100 C TOS-B4RJ1C o 0 to 200 C TOS-B4RJ2C o K T/c Relay 0 to 200 C TOS-B4RK2C o 0 to 400 C TOS-B4RK4C o 0 to 800 C TOS-B4RK8C o PT100 Relay 0 to 100 C TOS-B4RP1C For suitable panel mounting or DIN-rail wiring sockets see page 33. For +0 Panel cut-out 45 x 45 -0.5 thermocouples and PT100 probes see page 26. STANDARD ITEMS TC4800 ON/OFF & PD TEMPERATURE CONTROLLER Input Mode Output Range Part Number The TC4800 range of temperature o K T/c On/Off Relay 0 to 200 C TC4810-01-110/230VAC controllers is available in on/off or o K T/c On/Off Relay 0 to 400 C TC4810-02-110/230VAC proportional + derivative (PD) control o K T/c On/Off Relay 0 to 800 C TC4810-04-110/230VAC options, operating from a range of o K T/c On/Off Relay 0 to 1200 C TC4810-05-110/230VAC sensors. A 4 - 20mA input type also o J T/c On/Off Relay 0 to 200 C TC4810-11-110/230VAC enables them to be used for the o PT100 On/Off Relay -50 to 150 C TC4810-51-110/230VAC control of processes other than o PT100 On/Off Relay 0 to 100 C TC4810-52-110/230VAC temperature. Of particular note is the o PT100 On/Off Relay 0 to 200 C TC4810-53-110/230VAC dial lock which can be used to prevent o tampering. K T/c PD Relay 0 to 200 C TC4830-01-110/230VAC o K T/c PD Relay 0 to 400 C TC4830-02-110/230VAC o K T/c PD Relay 0 to 600 C TC4830-03-110/230VAC Dial lock J, K T/c, PT100 or 4 - 20mA inputs On/off or PD control action Deviation LEDs plus meter output For suitable panel mounting or DIN-rail wiring sockets see page 33. For Dual 110/230Vac supply input Relay or SSR drive output options thermocouples and PT100 sensors see page 26. 13 48 Sq TEMPERATURE CONTROLLERSANALOGUE PROCESS CONTROLLERS TR4800 TACHOMETER RELAY FSRS SHAFT ROTATION SENSOR The TR4800 series tachometer relay will The FSRS shaft rotation sensor is switch it s output at the speed selected on specifically designed to prevent access the front dial. The units are designed to to a normally rotating machine until it match the styling of the TC4800 temp- has slowed to a safe speed. An erature controllers and TT4800 Timers. adjustable potentiometer on the facia They offer a fast reaction time of <0.4sec enables the sensor to be set for an at 150rpm, have an internal supply to appropriate minimum speed which may power active sensors and a meter output be considered as safe for the operator to display the measured speed. The to gain access. If the sensor does not range consists of three models covering receive a pulse within the time set by speeds from 5 to 10,000 rpm. the potentiometer, it s output will ener- gise and this signal can be used to disable a guard. By using the normally 3 models for 5 to 10,000 rpm High speed response to input closed contacts the sensor becomes fail-safe in the event of loss of power 1mA meter output to display rpm Internal 15Vdc sensor supply SPECIFICATION SPECIFICATION Supply voltage : 110/230(220-240)Vac 50/60 Hz Supply voltage: 110/230(220-240)Vac 50/60 Hz or 24Vac/dc Power drain : 4VA Power drain: 3VA or 2 Watts max. Time delay : 1 to 30 seconds Scale accuracy: +/- 2% of full scale Sensing speed : Calculated by S = 60/nT rpm min Sensing ranges: 01: 5 to 100 rpm where n = No. of pulses per revolution 02: 50 to 1000 rpm T = time set on potentiometer 03: 500 to 10000 rpm Min. Pulse width: 3 msecs (for 50% duty cycle). To calculate the minimum Input sensor: Any volt-free contact or 3-wire active sensor with a flag width (W) use the formula W = r/10 mm ff power consumption of < 25mA at 15Vdc. See SI and (50% duty) where r = radius of shaft SC range of sensors on pages 29 and 30. Input sensor: Any volt-free contact (no bounce) or 3-wire active Output rating: SPCO relay rated at 5A/240Vac/30Vdc resistive Sensor with a power consumption of < 25mA at 24Vdc. Electrical life: 100,000 ops at rated load See SI or SC series sensors on pages 29 - 30. Metering output: 1 mAmp fsd at 75 Output rating: SPCO relay rated at 5A/240Vac/30Vdc resistive o Ambient range: -10 to 60 C non-condensing Electrical life: 100,000 ops at rated load o Approvals: Conforms to CE emc EN50081-1 & EN50082-1 and Ambient range: 10 to 50 C non-condensing low voltage EN61010-1 directives Approvals: Conform to CE emc EN50081-1 & EN50082-1 and low voltage EN61010-1 directives Part Numbering Options : TR4801-A-B CONNECTION DIAGRAM +24V NPN A Range 5 - 100 rpm 01 Sensor 50 - 1000 rpm 02 500 - 10000 rpm 03 - 6 7 5 8 B Power 110/230Vac 110/230VAC 4 supply 24Vac/dc 24VAC/DC 9 230V/24Vac 3 10 2 11 1 CONNECTION DIAGRAM N 110Vac +15V NPN Sensor 13 19 99 DIMENSIONS - 6 7 5 8 16 14 18 12 20 4 10 22 9 8 24 230V/24V 3 10 6 26 2 4 11 28 1 2 30 1 -0 N 110V Panel Cut-out 45 x 45 mm +0.5 STANDARD ITEM DIMENSIONS Type Delay Part Number 48 sq 74 15 17 Shaft Rotation Sensor 30 sec FSRST30SLP-110/230VAC Note: For suitable panel mounting or DIN rail wiring sockets see page 33. FLST LIQUID LEVEL DETECTOR The FLST liquid level detector has a fixed sensitivity, designed primarily to sense water using a conductive differ- -0 Panel Cut-out 45 x 45 mm +0.5 ential sensing device. By shorting the high and low probes, however, it can also be used for single point detection. STANDARD ITEMS Under differential operation, the output Type Range Part Number relay will energise when the liquid falls below the Low level and de-energise Tachometer relay 5 -100 rpm TR4801-01-110/230VAC when it rises above the High level. Tachometer relay 50 -1000 rpm TR4801-02-110/230VAC Tachometer relay 500 -10000 rpm TR4801-03-110/230VAC Differential or single point sensing Level indicating LEDs Note: For suitable panel mounting or DIN rail wiring sockets see page 33. Dual supply voltage 14 PROCESS CONTROLLERS 48 sq - + - +