28 10 54 6.2 14 Insulating gray The design and European Union marking. Double jacket wire to offer a wire wear indicator. The wire attachments The 4 mm banana male and female tip to prevent the material of the The lead complies with the Silicone wire for more flexibility at low temperatures comply with heavy duty. connections comply with the 4 mm banana sockets and plugs of the worldwide most accidental lantern contact European LVD by meeting and better feel. Cross section area 0.75 mm for famous manufacturers and meet the contact. springs meet the the harmonized standard currents up to 12 A. Lengths 50 cm, 100 cm (visible needs of low requirements of interchangeability EN / IEC 61010-031. length of the wire, not the overall length of the lead). resistance and dimensions of the standard reliability. NF C 93-440:1986. Fichier Datasheet TENMA 2210/600V. 28/11/2016. Indice A. Information in this publication supersedes all earlier versions. Specifications subject to change without notice. 2016. Dimensions in millimeters. ACCESSIBLE. Able to be touched with a standard test finger or test pin. BASIC INSULATION. Insulation of HAZARDOUS LIVE parts which provides basic protection. CAT II. Measurement or overvoltage category II. For measurement performed on / equipment connected to the building wiring. CAT III. Measurement or overvoltage category III. For measurement performed on / equipment connected to part of a building wiring installation. CAT IV. Measurement or overvoltage category IV. For measurement According to EN / IEC 61010-031:2008. 600 V CAT II, reinforced insulation, up to 36 performed on / equipment connected to the origin of the electrical supply to a building. A (at +40 C) depending on the wire. CLEARANCE. Shortest distance in air between two conductive parts. CREEPAGE DISTANCE. Shortest distance along the surface of a solid These specifications come from the creepage distances, clearances, accessible parts, and insulating material between two conductive parts. solid insulation of the lead. And the considered specifications of the environment are : CTI. Comparative Tracking Index of the insulating material in accordance pollution degree, 1 or 2 with IEC 60112. relative humidity, 80 % maximum for temperatures up to 31 C decreasing linearly to 50 DOUBLE INSULATION. Insulation comprising both BASIC INSULATION and SUPPLEMENTARY INSULATION. % relative humidity at +40 C EN / IEC 60529. European / international standard regarding the degrees of temperature range, +5 C to +40 C protection provided by enclosures. indoor use and EN / IEC 61010-1. European / international standard regarding the safety altitude, 2000 m maximum. requirements for electrical equipment for measurement, control, and laboratory use Part 1: General requirements. EN / IEC 61010-031. European / international standard regarding the safety Barrier. Keep behind this barrier to requirements for electrical equipment for measurement, control and laboratory use Part 031: Safety requirements for hand-held probe operate safely the lead while assemblies for electrical measurement and test. connecting to hazardous live voltages LV. European Directive 2014/35/EU on the harmonization of the laws of (more than 33 V AC and 70 V DC). Member States relating to electrical equipment designed for use within certain voltage limits. (Usually called the Low Voltage Directive.) -20 C mini., +80 C maxi. (please see above too). MAINS. Low-voltage electricity supply system to which the equipment concerned is designed to be connected for the purpose of powering the equipment. European DirectiveLow Voltage Directiv 2014/35/EU. MAINS CIRCUIT. Circuit which is intended to be directly connected to the International / European standard EN / IEC 61010-031:2008. MAINS for the purpose of powering the equipment. European DirectiveRoH 2011/65/UE. OVERVOLTAGE CATEGORY. Numeral defining a TRANSIENT European REACH regulation n 1907 / 2006. OVERVOLTAGE condition. Standard NF C 93-440:1986. POLLUTION. Addition of foreign matter, solid, liquid or gaseous (ionized gases), that may produce a reduction of dielectric strength or surface resistivity. RoH compliant, Pb 4 % in conductor, Pb 0.1 % in insulator, Hg 0.1 %, POLLUTION DEGREE. Numeral indicating the level of POLLUTION that Cr VI 0.1 %, Cd 0.01 %, PBB 0.1 %, and PBDE 0.1 %. may be present in the environment. REACH compliant, no substances from the candidate list of SVHC for authorisation at POLLUTION DEGREE 1. No POLLUTION or only dry, non-conductive mass concentrations greater than 0.1 %. POLLUTION occurs, which has no influence. POLLUTION DEGREE 2. Only non-conductive POLLUTION occurs except Conductors of the plugs : nickel-coated brass. Wire jackets : silicone. Insulators and that occasionally a temporary conductivity caused by condensation is expected. lantern contact spring, please contact us. REINFORCED INSULATION. Insulation which provides protection against electric shock not less than that provided by DOUBLE INSULATION. Black Red Yellow Green Blue White RoH. European Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment. 50 cm, 100 cm. SOLID INSULATION. Insulating materials. Designed and manufactured in France. SUPPLEMENTARY INSULATION. Independent insulation applied in addition to BASIC INSULATION in order to provide protection against electric shock in the event of a failure of BASIC INSULATION. Year of 1st placing on the market 1994. TRANSIENT OVERVOLTAGE. Short duration overvoltage of a few milliseconds or less, oscillatory or non-oscillatory, usually highly damped. One piece per bag. WORKING VOLTAGE. Highest r.m.s. value of the a.c. or d.c. voltage across any particular insulation which can occur when the equipment is supplied at rated voltage. Fichier Datasheet TENMA 2210/600V. 28/11/2016. Indice A. Information in this publication supersedes all earlier versions. Specifications subject to change without notice. 2016. Dimensions in millimeters.