TCR15AG series TOSHIBA CMOS Linear Integrated Circuit Silicon Monolithic TCR15AG series 1.5 A CMOS Ultra Low Dropout, Ultra High ripple rejection ratio Regulator The TCR15AG series are CMOS single output voltage regulators with an on/off control input, featuring Ultra low dropout voltage, low inrush current and fast load transient response. These voltage regulators are available in fixed output voltage type from 0.65 V to 3.6 V and adjustable output voltage type from 0.60 V to 3.6 V and capable of driving up to 1.5 A. Other features include Overcurrent protection, Thermal shutdown, Inrush current reduction, Under voltage lockout and Auto-discharge. WCSP6F The TCR15AG series are offered in the ultra-small package WCSP6F (0.8 Weight : 0.61 mg ( typ.) mm x 1.2 mm (typ.), t: 0.33 mm (max)) As small ceramic input and output capacitors can be used with the TCR15AG series, these device are ideal for portable applications that require high-density board assembly such as cellular phones. Features Low Drop-Out voltage Wide range Output Voltage (Fixed Output Voltage 0.65 V to 3.6 V ,Adjustable Output Voltage 0.6 V to 3.6 V) Fast load transient response -100 / +115 mV (typ.) 0.01 A1.5 A, COUT = 4.7 F High Ripple rejection ratio 95 dB (typ.) 1 kHz Overcurrent protection Thermal shutdown Auto-discharge Inrush current reduction Output voltage soft start Under voltage lockout Pull down connection between CONTROL and GND Ultra Small package WCSP6F (0.8 mm x 1.2 mm (typ.), t: 0.33 mm (max)) Stable with over 4.7 F Input capacitor, 1.0 F Bias capacitor and 4.7 F output ceramic capacitor Start of commercial production 2017-11 2017-11-08 2017 1 Toshiba Electronic Devices & Storage Corporation TCR15AG series Absolute Maximum Ratings (Ta = 25C) Characteristics Symbol Rating Unit Bias voltage V 6.0 V BIAS Input voltage V 6.0 V IN Control voltage V -0.3 to V + 0.3 6.0 V CT BIAS Adjustable voltage V -0.3 to 6.0 V ADJ Sense voltage V -0.3 to 6.0 V SENSE Output voltage V -0.3 to V + 0.3 6.0 V OUT IN Power dissipation P 1.35 (Note 1) W D Junction temperature T 150 C j Storage temperature range T 55 to 150 C stg Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note1: Rating at mounting on a board (Glass epoxy board dimension : 40mm x 40mm , 4 layer Metal pattern ratio : approximately 70% each layer) Operating Ranges Characteristics Symbol Rating Unit V 1.1 V, I = 1 mA 2.5 to 5.5 OUT OUT Bias voltage V V BIAS V > 1.1 V, I = 1 mA V + 1.4 V to 5.5 OUT OUT OUT Input voltage V V + V to V (Note 2) V IN OUT DO BIAS Control voltage V 0 to V V CT BIAS Output voltage V 0.6 to 3.6 (Note 3) V OUT Output current I 0 to 1.5 (Note 4) A OUT Operation Temperature T -40 to 85 C opr Output Capacitance C 4.7F OUT Input Capacitance CIN 4.7F BIAS Capacitance CBIAS 1.0F Note2: I = 1 mA. OUT Please refer to Dropout Voltage (Page 7) and use it within Absolute Maximum Ratings Junction temperature and Operation Temperature Ranges. Note3: For Output voltage adjustable type. Please refer to Application Note (Page 8). Note4: Do not operate at or near the maximum recommended current and temperature ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and results in failures not covered by warranty.Maximum recommended DC current specification defined as lifetime average junction temperature of +45C where max rated DC current = lifetime average current to avoid electro migration. 2017-11-08 2017 2 Toshiba Electronic Devices & Storage Corporation