TLP117 TOSHIBA PHOTOCOUPLER IRED & PHOTO-IC TLP117 PDP (Plasma Display Panel) Unit: mm FA (Factory Automation) High-Speed Interface The Toshiba TLP117 consists of an infrared emitting diode and an integrated high-gain, high-speed photodetector. Inverter logic (totempole output) Package type : MFSOP6 Guaranteed performance over temperature : -40 to 105C Power supply voltage : 4.5 to 5.5 V Input thresholds current : I =5 mA (max) FHL Propagation delay time (tpHL/tpLH) : 30 ns (max) at VL=0 V : 20 ns (max) at VL=1.1 V TOSHIBA 11-4C2 Switching speed : 50 MBd (typ.) Weight: 0.09 g (typ.) Common mode transient immunity : 10 kV/ s (min) Isolation voltage : 3750 Vrms UL-recognized : UL 1577, File No.E67349 cUL-recognized : CSA Component Acceptance Service No.5A File No.E67349 VDE-approved : EN 60747-5-5 (Note 1) Note 1 : When a VDE approved type is needed, please designate the Option(V4). Truth Table Pin Configuration (Top View) Input LED M1 M2 Output H ON OFF ON L 1:ANODE 1 6 V CC L OFF ON OFF H 3:CATHODE 5 4:GND 5: V O GND 6: V 3 4 CC SHIELD Schematic ICC V CC 6 I F M1 1+ I O VF V O 3- M2 5 GND 4 SHIELD 0.1 F bypass capacitor must be Start of commercial production connected between pins 6 and 4 2007-05 2019 1 2019-05-27 Toshiba Electronic Devices & Storage Corporation TLP117 Absolute Maximum Ratings (Ta=25C) Characteristic Symbol Rating Unit Forward current I 25 mA F Forward current derating (Ta85C) IF/ Ta -0.7 mA/C Peak transient forward current (Note 1) I 1 A FPT Reverse voltage V 6 V R Diode power dissipation PD 40 mW Diode power dissipation derating (Ta85C) P / Ta -1.0 mW/C D Output current I 10 mA O Output voltage V 6 V O Supply voltage V 6 V CC Output power dissipation P 40 mW O Operating temperature range T -40 to 105 C opr Storage temperature range T -55 to 125 C stg Lead solder temperature(10 s) T 260 C sol Isolation voltage (AC,60 s, R.H. 60 %, ) (Note 2) BVs 3750 Vrms Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Pulse width PW 1 s, 300 pps. Note 2: This device is regarded as a two-terminal device: pins 1 and 3 are shorted together, and pins 4,5 and 6 are shorted together. Recommended Operating Conditions Characteristic Symbol Min Typ. Max Unit Input current , ON I 10 16 mA F(ON) Input voltage , OFF V 0 1.0 V F(OFF) Supply voltage(*) (Note 1) 4.5 5.0 5.5 V V CC * This item denotes operating ranges, not meaning of recommended operating conditions. Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the device. Additionally, each item is an independent guideline respectively. In developing designs using this product, please confirm specified characteristics shown in this document. Note 1: The detector of this product requires a power supply voltage (V ) of 4.5 V or higher for stable operation. If CC V is lower than this value, I may increase or the output may be unstable. CC CC Be sure to use the product after checking the supply current, and the operation of a power-on/-off. 2019 2 2019-05-27 Toshiba Electronic Devices & Storage Corporation LED DETECTOR