TLP700 TOSHIBA Photocoupler GaAAs IRED + Photo IC TLP700 Industrial inverters Unit: mm Inverter for air conditioners 4.580.25 IGBT/Power MOSFET gate drive 6 5 4 TLP700 consists of a GaAAs light-emitting diode and an integrated photodetector. This unit is 6-lead SDIP package. The TLP700 is 50% smaller than the 8-pin DIP and meets the reinforced insulation class requirements of international safety standards. Therefore the mounting area can be reduced in equipment requiring safety standard certification. 1 2 3 The TLP700 is suitable for gate driving circuits for IGBTs or power MOSFETs. In 7.620.25 particular, the TLP700 is capable of direct gate driving of low-power IGBTs. Peak output current: 2.0 A (max) Guaranteed performance over temperature: 40 to 100C 1.270.2 1.250.25 Supply current: 2 mA (max) 0.40.1 9.70.3 Power supply voltage: 15 to 30 V Threshold input current: I = 5 mA (max) FLH 11-5J1 Switching time (t / t ): 500 ns (max) pLH pHL TOSHIBA 11-5J1 Common mode transient immunity: 15 kV/s (min) Weight: 0.26 g (typ.) Isolation voltage: 5000 Vrms (min) Construction mechanical rating Pin Configuration (Top View) 7.62-mm pitch 10.16-mm pitch standard type TLPXXXF type 1: ANODE 1 6 Creepage Distance 7.0 mm (min) 8.0 mm (min) 2: N.C Clearance 7.0 mm (min) 8.0 mm (min) 3: CATHODE Insulation Thickness 0.4 mm (min) 0.4 mm (min) 2 5 4: GND 5: V ( OUTPUT ) O UL recognized: UL1577, File No. E67349 6: V 4 CC 3 SHIELD Option (D4) type TV approved: EN60747-5-2 Schematic Maximum operating insulation voltage: 890 Vpk I CC Highest permissible over voltage: 8000 Vpk V CC (M1) ( Note ) When a EN60747-5-2 approved type is needed, 6 I F please designate the Option(D4) 1 I O V F (M2) 3 V O 5 GND SHIELD 4 Truth Table A 0.1-F bypass capacitor must be connected Input LED M1 M2 Output between pins 6 and 4. (See Note 6) H ON ON OFF H OFF OFF ON L L Start of commercial production 2007/08 1 2014-09-22 +0.15 3.65 6.80.25 0.25 +0.10 0.25 0.05 +0.25 4.0 0.20 TLP700 Absolute Maximum Ratings (Ta = 25 C) Characteristics Symbol Rating Unit Forward current I 20 mA F Forward current derating (Ta 85C) I /Ta 0.54 mA/C F Peak transient forward current (Note 1) I 1 A FP Reverse voltage V 5 V R Junction temperature T 125 C j H peak output current I 2.0 A Ta=-40 to 100 C OPH (Note 2) L peak output current I 2.0 A OPL Output voltage V 35 V O Supply voltage V 35 V CC Junction temperature T 125 C j Operating frequency (Note 3) f 50 kHz Operating temperature range T 40 to 100 C opr Storage temperature range T 55 to 125 C stg Lead soldering temperature (10 s) (Note 4) T 260 C sol Isolation voltage (AC, 1 minute, R.H. 60%) (Note 5) BV 5000 Vrms S Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Pulse width P 1 s, 300 pps W Note 2: Exponential waveform pulse width P 0.3 s, f 15 kHz W Note 3: Exponential waveform I 1.5 A ( 0.3 s), I +1.5 A ( 0.3 s), Ta=100C OPH OPL Note 4: For the effective lead soldering area Note 5: Device considered a two-terminal device: pins 1, 2 and 3 paired with pins 4, 5 and 6 respectively. Note 6: A ceramic capacitor (0.1 F) should be connected from pin 6 to pin 4 to stabilize the operation of the high gain linear amplifier. Failure to provide the bypassing may impair the switching property. The total lead length between capacitor and coupler should not exceed 1 cm. Recommended Operating Conditions Characteristics Symbol MinTyp.MaxUnit Input current, ON (Note 7) I 7.5 10 mA F (ON) Input voltage, OFF V 0 0.8 V F (OFF) Supply voltage * (Note 8) V 15 30 V CC Peak output current I / I 1.5 A OPH OPL Operating temperature T 40 100 C opr * This item denotes operating ranges, not meaning of recommended operating conditions. Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the device. Additionally, each item is an independent guideline respectively. In developing designs using this product, please confirm specified characteristics shown in this document. Note 7: Input signal rise time (fall time) 0.5 s. Note 8: If the V rise slope is sharp, an internal circuit might not operate with stability. Please design the V rise CC CC slope under 3.0 V/s. 2 2014-09-22 Detector LED