Long Distance Reflective Switch OPB720A and OPB720B Series Features: 0.04 to 12 (1 mm to 305 mm) with 90% reflective material. (Typical Maximum detection distance to be set at factory) Recognizes objects as small as 0.08 (2 mm) Ambient light rejection < 100K Lux Open collector output Cable length 39 (990 mm) lead length 28 AWG wire Description: The OPB720A and OPB720B Series reflective switches detects objects as far away as 12 (305 mm) using standard 90% reflective material, and can detect objects as small as 0.08 (2 mm). The OPB720 series consist of three standard reflective switching distances -06Z for typically 6 (152 mm), -12Z for typically 12 (305 mm) and -30VZ for typically 30 (762 mm). The power supply voltage range of the OPB720A series is 10 to 30 volts while the power supply voltage range for the OPB720B is 4 to 7 volts. The OPA720A and OPB720B sensors are NOT affected by ambient light in most conditions. Ambient light conditions are compensated by using a synchronous driver detection scheme. This sensor has a logical output that switches from a high level with reflective target to a low level with no reflective target. With the addition of hysteresis, the OPB720 series minimizes output switching oscillations. The type of material used for the target is very dependent on the distance that can be achieved for the sensor. Taking this into consideration, the OPB720 series can be used in either a reflective or interruptive mode. As an example, the OPB720A-12Z can easily be used in a reflective mode for distances around 12 (305 mm) while when reflecting off a retro-reflective target similar to 3M 3870 or Nippon Crystallite at distances around 85 (216 mm) the device works well in the interruptive mode. See the included charts for typical distances with different reflective material for other versions of the OPB720 series devices. The OPB720 series has an open collector output transistor and power requirements are compatible with most PLCs and TTL gates. Ordering Information Applications: Part Number Description Conveyer belt package recognition Personnel movement recognition Maximum detection of 0.04 to 6 (1.0 mm to 152 mm) OPB720A-06Z Near-focus security systems 39 (991 mm) lead length with 28 AWG wire, using white 90% OPB720B-06Z reflective paper Hand wash and soap dispensing stations Toilet and urinal sensors Maximum detection of 0.04 to 12 (1.0 mm to 305 mm) OPB720A-12Z Product dispensing systems 39 (991 mm) lead length with 28 AWG wire, using white 90% OPB720B-12Z reflective paper Maximum detection of 0.04 to 30 (1.0 mm to 762 mm) Vcc OPB720A-30VZ 39 (991 mm) lead length with 28 AWG wire, using white 90% OPB720B-30VZ reflective paper Electronics Output OPB720A-30VZ & OPB720B-30VZ ONLY Additional laser safety information can be found on the Optek website. See application 221. Classification is not marked on the device due to space limitations. See package outline for Ground centerline of optical radiance. Operating de- vices beyond maximum rating may cause de- vices to exceed rated classification OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. RoHS OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Issue F.1 01/08 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors optekinc.com www.optekinc.com Page 1 of 5 Long Distance Reflective Switch OPB720A and OPB720B Series Pin Description Red V CC White Output MILLIMETERS Black Ground DIMENSIONS ARE IN: INCHES Absolute Maximum Ratings (T =25C unless otherwise noted) A Operating Temperature Range OPB720A Series 0 C to + 50 C OPB720B Series 0 C to + 70 C Storage Temperature Range -40 C to + 80 C (1) Lead Soldering Temperature (1/16 (1.6 mm) from case for 5 seconds with soldering iron) 260 C Supply Voltage (V ) CC OPB720A Series 10 to 30 Volts OPB720B Series 4 to 7 Volts Maximum Collector Voltage 30 V Collector DC Current (Sink) 50 mA Power Dissipation 300 mW Electrical Characteristics (T = 25C unless otherwise noted) A SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Low Level Output Voltage V OPB720A Series - - 0.8 V = 10 Volts, Note 4 OL CC V OPB720B Series - - 0.8 V = 4 Volts, Note 4 CC High Level Output Voltage V OPB720A Series 5.0 - - V = 10 Volts, Note 5 OH CC V OPB720B Series 3.5 - - V = 4 Volts, Note 5 CC Notes: (1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when flow soldering. (2) Distance for OPB720A-06Z=6 (152 mm), Distance for OPB720A-12Z=12 (305mm), Distance for OPB720A-30VZ=30 (762 mm) (3) OPB720A-30VZ & OPB720B-30VZ are class 1M laser safety device. Do Not look at the device closer than 4 (100 mm) with a magnifying device. (4) R = 10 K, V = V Distance = See Note 2 & 3, (No Target) L CE CC (5) R = 10 K, V = V (90% Reflective Surface, KodakEK E152-7798) L CE CC, OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue F.1 01/08 OPTEK Technology Inc. 1645 Wallace Drive, Carrollton, Texas 75006 Page 2 of 5 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors optekinc.com www.optekinc.com