CATALOG 128_CATALOG 128.qxd 4/25/2014 7:15 AM Page 76
PCB Accessories
Tools & Handles
Pad Cutters, Insertion Tools
Hand Insertion Tools for
Pad Cutters
Push-In Terminals
Terminal
Part Holder Type
P/N
No
T44
A13 Shank with removable rubber handle
A13-1 T68 Shank with removable rubber handle
T28
P91A Wooden Handle
T49
P156 Wooden Handle
T46 series
P133A Shank with removable rubber handle
& K24 - K31
P134 K36 Wooden Handle
T42-1
P149A Wooden Handle
T42-1
P149 Shank with removable rubber handle
A13 Shank with removable rubber handle
Shank Type
(A13 type)
P149 Shank with removable rubber handle
P149A - Wooden Handle Type
Shows pad removal
T107
& pad cutter P116C
Shank Only
Bus Strips
P138C
P138A
Wooden Handle type
Vector Pad Cutters provide an effective method for cre-
ating isolated solder pads around holes in copper clad
boards. Pilot pin enters hole and rotates, creating a
Flat cold-drawn flat copper wire, 0.017 thick (+/-0.003)
clearance area around the solder pad. Available for 0.080W with 0.042 diameter holes on 0.100 centers
Hot 100% Tin dipped, fully RoHS compliant
boards with.062 or .042 diameter holes. Also available
Compatible with most Vectorbord hole patterns
without handles for use with manual or power drills.
Part
Holder A B C Shank Use with
Part No. Pkg Qty
No. Type
Vectorbord
P116C Handle/Shank .055 .188 .250 .250
Pattern G, H .062 holes
T107/C 100
P138A Handle/Shank .040 .086 .125 .125
Pattern P, .042: holes
T107/10
10
P138C Shank Only .040 .086 .125 .125 Pattern P, .042: holes
HA14
HA9
Pull Type Ejector Handle
Rotation Type Ejector Handle
Package
Part No.
Extraction/insertion handles
Quantity
Mounts on front edge of
HA14 4
tm
Plugbord with single screw
HA14/C 100
or roll-pin
Plastic (FE4)
Dimensional information for HA9 is on Page 44
Card ejector, corner mounting
Part No.
Pkg Qty
Supports up to 40 lbs
HA9/4
extraction force
4
HA9/C
White nylon, (hardware included) 100
76
www.vectorelect.com Specification subject to change without notice 800-423-5659
Tools
Pad CutterCATALOG 128_CATALOG 128.qxd 4/25/2014 7:17 AM Page 78
PCB Accessories
Tefzel 28 AWG Wire Insulation Properties
Slit-N-Wrap Wire
Property Test Method Unit Value
Thermal Properities
Tefzel Insulated Silver Plated Wire for
o
Nominal Melting Point ASTM D3159 C 255-280
use with No. 02 Bit
o
( F) (491-536)
Flow Rate ASTM D315 g/10 min 20
Part No. AWG Color Spool Dia. Feet/Spool Spools/Pkg
o
Upper Service Temperature UL746 C 135
W28-6A 28 green 1 50 2
W28-6B 28 red 1 50 2
W28-6D 28 blue 1 50 2
Mechanical Properities
o o W28-6E 28 white 1 50 2
Tensile Strength, 23 C (73 F) ASTM D3159 MPa, (psi) 40, (6,500)
W28-6F 28 yellow 1 50 2
Specific Gravity ASTM D792 - 1.71
W28-6H 28 black 1 50 2
o o
Ultimate Elongation, 23 C (73 F) ASTM D3159 % 300
W28-6AU 28 green 1.5 150 1
o o
Flexural Modulus, 23 C (73 F) ASTM D790 MPa (psi) 1,200 (170,000)
W28-6BU 28 red 1.5 150 1
o o
Impact Streength, 23 C (73 F) ASTM D256 J/m (ft-lb/in.) No Break
W28-6DU 28 blue 1.5 150 1
Hardness, Durometer ASTM D2240 Shore D 63
W28-6EU 28 white 1.5 150 1
Compressive Strength ASTM D695 MPa, (psi) 38 (5,500)
W28-6FU 28 yellow 1.5 150 1
o -5
W28-6HU 28 black 1.5 150 1
Linear Coefficient of Expansion, ASTM E831 mm/mm/ C 12.6x 10
o o o -5
0-100 C (32-212 F) in./in./ F (7.0 x 10 )
See specifications on Page 81
Electrical Properities
Dielectric Strength, 0.25mm (0.010in.) ASTM D149 kV/mm (V/0.001in.) 70 (1,800)
o o
Dielectric Constant, 1MHz,23 C (73 F) ASTM D1531 - 2.5-2.6
o o
Dissipation Factor, 1MHz,23 C (73 F) ASTM D1531 - 0.00540
3 17
.
Volume Resistivity ASTM D257 ohm cm 1 x 10 (1 x 10 )
Arc Resistance ASTM D49 seconds 122
General Properities
Water Absorption, 24 h ASTM D570 % 0.007
Weather and Chemical Resistance - - Excellent
Limiting Oxygen Index ASTM D2863 % 30-32
Vector 28AWG Tefzel wire is rated 300V at 150 degrees C
T120-1 EyeletsT15.23,T123
Slip-On Contacts
2 versions provide hole size
reduction
Reels of slip-on contacts. 5 apart
T123 - reduces .055 dia. holes
Slips onto .025 square posts
to .042
28 gage PVC insulated blue wire
T123 eyelets are copper with
o
Temperature Range: -310 to 221 F
.0003 to .0005 thick tin plating
o
(-190 to 105 C)
T15.23 - reduces .062 dia. holes
to .042
Simulates copper thru hole
plating
Used to commit power and
ground planes
ID
B
.04 + .02
1.0 + 0.5
Contact
No Contact
Body
Detail
Board C
Black
Contact
Shrinkable A
.060
T123 Eyelet
T123 Eyelet
No Contact
REF Tubing
1.52
End Terminal Only
Part No. Qty A B C ID
T15.23/M 1000 .062 .105 .093 .042
Contact Package
T123/500 500 .055 .105 .093 .042
Part No.
Description Quantity. T123/1000 1000 .055 .105
.093 .042
installed on wire Reel of 50
T120-1/50
installed on wire Reel of 250
T120-1/250
78
www.vectorelect.com Specification subject to change without notice 800-423-5659
Accessories